Share with friends:
Car maintenance Renault Clio 1
Introduction to the Renault Clio
The Renault Clio series of models described in this book, which replaced the popular Renault 5 series, was introduced in May 1990. Renault Clio is equipped with petrol engines of 1.1, 1.2, 1.7 and 1.8 liters (there is a...
The Renault Clio series of models described in this book, which replaced the popular Renault 5 series, was introduced in May 1990. Renault Clio is equipped with petrol engines of 1.1, 1.2, 1.7 and 1.8 liters (there is a...
Dimensions and weight of the car
Note: All data is approximate and may vary depending on the model. See manufacturer's data. Dimensions Overall length 3709 - 3716 mm Overall width (without outside mirrors) 1616 - 1641 mm Full height (unloaded) 1365 -...
Note: All data is approximate and may vary depending on the model. See manufacturer's data. Dimensions Overall length 3709 - 3716 mm Overall width (without outside mirrors) 1616 - 1641 mm Full height (unloaded) 1365 -...
Lubricants and fluids
Engine Universal motor oil, viscosity 15W/40 - 15W/50, ACEA A2/AZ Manual transmission Tranself TRX 75W 80W Automatic transmission Without final drive Elf Renaultmatic D2, ATF Dexron Main gear Transeff TRX 80W Power...
Engine Universal motor oil, viscosity 15W/40 - 15W/50, ACEA A2/AZ Manual transmission Tranself TRX 75W 80W Automatic transmission Without final drive Elf Renaultmatic D2, ATF Dexron Main gear Transeff TRX 80W Power...
Tire pressures (cold)
Front* Rear 145/70 R 138 2.4 bar 2.4 bar 155/70 R 138 and 165/65 R 13T 2.1 bar 2.3 bar 145/80 R 138 and 155/80 R 13T 2.1 bar 2.1 bar 165/60 R 14H 2.3 bar 2.3 bar 185/60 R 147 and 185/55 R 157 2.2 bar 2.2 bar *For models...
Front* Rear 145/70 R 138 2.4 bar 2.4 bar 155/70 R 138 and 165/65 R 13T 2.1 bar 2.3 bar 145/80 R 138 and 155/80 R 13T 2.1 bar 2.1 bar 165/60 R 14H 2.3 bar 2.3 bar 185/60 R 147 and 185/55 R 157 2.2 bar 2.2 bar *For models...
Service Specifications
Filling volumes Motor oil Without oil filter: C-series engine 3.0 liters Engines 1171 cm³ and 1390 cm³ E-series 3.5 liters F3P engines 4.7 liters F7P engine (with 16 valves): With steel pallet 3.5 liters With an...
Filling volumes Motor oil Without oil filter: C-series engine 3.0 liters Engines 1171 cm³ and 1390 cm³ E-series 3.5 liters F3P engines 4.7 liters F7P engine (with 16 valves): With steel pallet 3.5 liters With an...
Identification number
When ordering spare parts, always provide as much information about your vehicle as possible. Please provide the model, year of manufacture, chassis and engine numbers. The identification plate is riveted to the top of...
When ordering spare parts, always provide as much information about your vehicle as possible. Please provide the model, year of manufacture, chassis and engine numbers. The identification plate is riveted to the top of...
Weekly checks
Introduction There are some very simple checks that will only take a few minutes and will protect you from inconvenience and unnecessary expenses. These "Weekly Checks" do not require any qualifications or special...
Introduction There are some very simple checks that will only take a few minutes and will protect you from inconvenience and unnecessary expenses. These "Weekly Checks" do not require any qualifications or special...
Weekly under-hood checkpoints
Check points under the hood D-series engine (1149 cc) : A - Engine oil level dipstick; B - Engine oil filler cap; C - Coolant expansion tank; D - Brake fluid reservoir; E - Washer reservoir; F - Power steering...
Check points under the hood D-series engine (1149 cc) : A - Engine oil level dipstick; B - Engine oil filler cap; C - Coolant expansion tank; D - Brake fluid reservoir; E - Washer reservoir; F - Power steering...
Engine oil level
Before you start Make sure your car is on level ground. Check the oil level before starting the engine, or at least 5 minutes after turning off the engine. The right oil Modern engines place high demands on oil....
Before you start Make sure your car is on level ground. Check the oil level before starting the engine, or at least 5 minutes after turning off the engine. The right oil Modern engines place high demands on oil....
Coolant level
Warning: DO NOT attempt to remove the expansion tank pressure cap while the engine is still hot, as this can cause burns. Do not leave containers of coolant open, as it is poisonous. Precautions: Regular addition of...
Warning: DO NOT attempt to remove the expansion tank pressure cap while the engine is still hot, as this can cause burns. Do not leave containers of coolant open, as it is poisonous. Precautions: Regular addition of...
Brake fluid level
Warning: Brake fluid can be harmful to your eyes and painted surfaces, so use extreme caution when handling. Do not use fluid that has been open for some time as it will absorb moisture from the air, causing loss of...
Warning: Brake fluid can be harmful to your eyes and painted surfaces, so use extreme caution when handling. Do not use fluid that has been open for some time as it will absorb moisture from the air, causing loss of...
Power steering fluid level
Before you begin: Park the car on a level place. Set the front wheels to drive straight ahead. Check the fluid level with the engine off. Safety! The need for frequent refilling indicates a leak that must be repaired...
Before you begin: Park the car on a level place. Set the front wheels to drive straight ahead. Check the fluid level with the engine off. Safety! The need for frequent refilling indicates a leak that must be repaired...
Tire condition and pressure
It is very important to keep your tires in good condition and at the correct pressure - a tire failure at any speed is very dangerous. Tyre wear is affected by driving style - hard braking and acceleration, or fast...
It is very important to keep your tires in good condition and at the correct pressure - a tire failure at any speed is very dangerous. Tyre wear is affected by driving style - hard braking and acceleration, or fast...
Tire tread wear patterns
Marginal wear Insufficient pressure (wears out on both sides) Underinflation causes the tire to overheat because the cord will bend too much and the tread will not sit properly on the road surface. This will cause loss...
Marginal wear Insufficient pressure (wears out on both sides) Underinflation causes the tire to overheat because the cord will bend too much and the tread will not sit properly on the road surface. This will cause loss...
Battery — periodic inspection
Make sure the battery tray is in good condition. Corrosion on the tray, clamp and battery can be removed with a solution of baking soda and water. Rinse all cleaned areas thoroughly with water. All metal parts damaged...
Make sure the battery tray is in good condition. Corrosion on the tray, clamp and battery can be removed with a solution of baking soda and water. Rinse all cleaned areas thoroughly with water. All metal parts damaged...
Windshield wipers
1. Check the condition of the wiper blades: replace the blades if they are cracked or show signs of wear. Windshield wipers should be replaced annually. 2. To remove the wiper blade, pull the arm completely away from...
1. Check the condition of the wiper blades: replace the blades if they are cracked or show signs of wear. Windshield wipers should be replaced annually. 2. To remove the wiper blade, pull the arm completely away from...
Lamps and fuses
Check all external lights and horn. See the relevant Chapters Section 12 . Visually inspect all wiring connectors, harnesses, and mounting brackets for secure connections and for signs of fraying or damage. 1. If the...
Check all external lights and horn. See the relevant Chapters Section 12 . Visually inspect all wiring connectors, harnesses, and mounting brackets for secure connections and for signs of fraying or damage. 1. If the...
Washer fluid level in the reservoir
Windshield washer fluid additives not only contain cleaning additives, they also prevent the washer system from freezing. Do not add plain water, as the windshield washer fluid will become too dilute and freeze in cold...
Windshield washer fluid additives not only contain cleaning additives, they also prevent the washer system from freezing. Do not add plain water, as the windshield washer fluid will become too dilute and freeze in cold...
Maintenance — frequency
The maintenance procedures in this manual are designed with the assumption that the vehicle owner will perform the work himself. The intervals indicated are recommended by the manufacturer for vehicles used daily. If...
The maintenance procedures in this manual are designed with the assumption that the vehicle owner will perform the work himself. The intervals indicated are recommended by the manufacturer for vehicles used daily. If...
General description of maintenance
This Section is designed to help the owner maintain the vehicle in good condition so that it operates safely, economically and for a long time. The chapters in this section describe maintenance procedures in sequence,...
This Section is designed to help the owner maintain the vehicle in good condition so that it operates safely, economically and for a long time. The chapters in this section describe maintenance procedures in sequence,...
Intensive service
1. If the suggested maintenance program is followed correctly, and fluid levels are checked frequently and components with high wear potential are inspected, the engine of a new vehicle will remain in good working order...
1. If the suggested maintenance program is followed correctly, and fluid levels are checked frequently and components with high wear potential are inspected, the engine of a new vehicle will remain in good working order...
Every 10,000 km or 6 months — Change engine oil and filter
1. Before you begin this procedure, prepare all the necessary tools and materials (see illustration). Also prepare rags and old newspapers to wipe up spills. It is better for the engine oil to be warm, this will allow...
1. Before you begin this procedure, prepare all the necessary tools and materials (see illustration). Also prepare rags and old newspapers to wipe up spills. It is better for the engine oil to be warm, this will allow...
Every 10,000 km or 6 months — check the transmission fluid level
Note: The procedure for checking the automatic transmission fluid level is very complex, so it is best to contact your Renault dealer. Main transmission 1. First, add 0.5 L of the specified fluid to the transmission by...
Note: The procedure for checking the automatic transmission fluid level is very complex, so it is best to contact your Renault dealer. Main transmission 1. First, add 0.5 L of the specified fluid to the transmission by...
Every 10,000 km or 6 months — check for fluid leaks
1. Visually inspect the connection points of various engine components, gaskets and seals for signs of leaks. Pay special attention to the areas surrounding the camshaft cover, cylinder head, oil filter and oil pan....
1. Visually inspect the connection points of various engine components, gaskets and seals for signs of leaks. Pay special attention to the areas surrounding the camshaft cover, cylinder head, oil filter and oil pan....
Every 10,000 km or 6 months — check the auxiliary drive belt
Note: Before working around the generator, disconnect the negative battery cable. General description 1. The type and quantity of auxiliary drive belts may vary depending on the model. To check the condition of the...
Note: Before working around the generator, disconnect the negative battery cable. General description 1. The type and quantity of auxiliary drive belts may vary depending on the model. To check the condition of the...
Every 10,000 km or 6 months — check idle speed and mixture
Warning: Do not run the engine in a closed area (there is a risk of carbon monoxide poisoning). Carburetor models Note: To accurately perform this procedure, you will need a tachometer and exhaust gas analyzer. 1....
Warning: Do not run the engine in a closed area (there is a risk of carbon monoxide poisoning). Carburetor models Note: To accurately perform this procedure, you will need a tachometer and exhaust gas analyzer. 1....
Every 10,000 km or 6 months — Check spark plugs
1. The correct operation and performance of the engine depends on the correct functioning of the spark plugs. It is important that the spark plugs installed are suitable for the engine (the appropriate type is defined...
1. The correct operation and performance of the engine depends on the correct functioning of the spark plugs. It is important that the spark plugs installed are suitable for the engine (the appropriate type is defined...
Every 10,000 km or 6 months — check the contact plates of the breaker (c-series engine)
1. Release the two spring clips and remove the distributor cap. Pull the distributor rotor off the shaft and remove the plastic shield (see illustration). 9.1 Remove the distributor rotor from the contact breaker. 2....
1. Release the two spring clips and remove the distributor cap. Pull the distributor rotor off the shaft and remove the plastic shield (see illustration). 9.1 Remove the distributor rotor from the contact breaker. 2....
Every 10,000 km or 6 months — check ignition timing (c-series engine)
1. For the engine to operate efficiently, it is necessary for the spark in the spark plug to ignite the fuel-air mixture at the moment when the piston has not yet reached top dead center on the compression stroke. The...
1. For the engine to operate efficiently, it is necessary for the spark in the spark plug to ignite the fuel-air mixture at the moment when the piston has not yet reached top dead center on the compression stroke. The...
Every 10,000 km or 6 months — check the clutch operation
Note: The following test is not specified by Renault. 1. Press the clutch pedal several times and make sure that it moves easily and without jerking, and that the clutch functions correctly, without slipping or...
Note: The following test is not specified by Renault. 1. Press the clutch pedal several times and make sure that it moves easily and without jerking, and that the clutch functions correctly, without slipping or...
Every 10,000 km or 6 months — check the exhaust system
1. The exhaust system is checked on a cold engine. To facilitate inspection, raise the vehicle and support it on axle stands so that all exhaust components are visible and accessible. 2. Check exhaust pipes and...
1. The exhaust system is checked on a cold engine. To facilitate inspection, raise the vehicle and support it on axle stands so that all exhaust components are visible and accessible. 2. Check exhaust pipes and...
Every 10,000 km or 6 months — check front brake pads and discs
1. Apply the handbrake, then jack up the front of the car and support it on axle stands. Remove the front wheels. 2. You can quickly check the thickness of the lining on each brake pad through the hole in the caliper....
1. Apply the handbrake, then jack up the front of the car and support it on axle stands. Remove the front wheels. 2. You can quickly check the thickness of the lining on each brake pad through the hole in the caliper....
Every 10,000 km or 6 months — check rear brake pads and discs
1. Block the front wheels, then jack up the rear of the vehicle and support it on axle stands. Remove the rear wheels. 2. You can quickly check the thickness of the lining on each brake pad through the hole in the...
1. Block the front wheels, then jack up the rear of the vehicle and support it on axle stands. Remove the rear wheels. 2. You can quickly check the thickness of the lining on each brake pad through the hole in the...
Every 10,000 km or 6 months — check the condition of the body and underbody
1. Wash the car thoroughly, remove all tar stains and other dirt, then carefully inspect the entire paintwork, looking for scratches and chips. Pay special attention to the most vulnerable areas (hood, spoilers and...
1. Wash the car thoroughly, remove all tar stains and other dirt, then carefully inspect the entire paintwork, looking for scratches and chips. Pay special attention to the most vulnerable areas (hood, spoilers and...
Every 10,000 km or 6 months — check the direction of the light beam
1. Accurately checking and adjusting the direction of the light beam can only be done using special optical equipment, and this work must be entrusted to a Renault dealer. 2. In case of emergency, the direction of the...
1. Accurately checking and adjusting the direction of the light beam can only be done using special optical equipment, and this work must be entrusted to a Renault dealer. 2. In case of emergency, the direction of the...
Every 10,000 km or 6 months — check steering and suspension components
Front suspension and steering gear 1. Jack up the front of the vehicle and place it on axle stands. 2. Visually inspect the ball joint dust caps and steering gear rubber boots for cracks, abrasions, or contamination...
Front suspension and steering gear 1. Jack up the front of the vehicle and place it on axle stands. 2. Visually inspect the ball joint dust caps and steering gear rubber boots for cracks, abrasions, or contamination...
Every 10,000 km or 6 months — check the drive shaft boot
1. Jack up the vehicle and place it on axle stands, turn the steering wheel all the way, and then slowly turn the wheel. Check the condition of the outer CV joint rubber boots. Check for signs of cracking or...
1. Jack up the vehicle and place it on axle stands, turn the steering wheel all the way, and then slowly turn the wheel. Check the condition of the outer CV joint rubber boots. Check for signs of cracking or...
Every 10,000 km or 6 months — check the tightness of the wheel bolts
1. Where applicable, remove the wheel caps and loosen the wheel bolts slightly. 2. Tighten the bolts to the torque specified in the Specifications (use a torque wrench).
1. Where applicable, remove the wheel caps and loosen the wheel bolts slightly. 2. Tighten the bolts to the torque specified in the Specifications (use a torque wrench).
Every 10,000 km or 6 months — check the heating and air conditioning systems
1. Make sure the heating system is working properly. See Section 3, Chapter 11 . 2. On models with air conditioning, ensure the system is working properly. Start the engine and turn on the air conditioner to maximum...
1. Make sure the heating system is working properly. See Section 3, Chapter 11 . 2. On models with air conditioning, ensure the system is working properly. Start the engine and turn on the air conditioner to maximum...
Every 20,000 km — Replace the air filter element
C-series engine 1. Release the spring clips and remove the wing nut from the air cleaner cover (see illustration). 21.1 Remove the air cleaner cover - C-series engine: 2 - Wing nut; 3 - Spring clamp. E-series engines 2....
C-series engine 1. Release the spring clips and remove the wing nut from the air cleaner cover (see illustration). 21.1 Remove the air cleaner cover - C-series engine: 2 - Wing nut; 3 - Spring clamp. E-series engines 2....
Every 20,000 km — check high-tension wires, distributor cap and rotor
1. Check the high-voltage wiring whenever new spark plugs are installed. 2. Before removing the wires, make sure that they are numbered accordingly so as not to get confused during installation (see illustrations)....
1. Check the high-voltage wiring whenever new spark plugs are installed. 2. Before removing the wires, make sure that they are numbered accordingly so as not to get confused during installation (see illustrations)....
Every 20,000 km — test drive
Instruments and electrical equipment 1. Check the functioning of all devices and electrical equipment. 2. Make sure all instruments are giving correct readings. Turn on all electrical equipment one by one and make sure...
Instruments and electrical equipment 1. Check the functioning of all devices and electrical equipment. 2. Make sure all instruments are giving correct readings. Turn on all electrical equipment one by one and make sure...
Every 58,000 km — check the air temperature control system
Note: This procedure only applies to engines with a carburetor or central fuel injection system. 1. For the engine to operate efficiently, the temperature of the air entering the intake system must be maintained at a...
Note: This procedure only applies to engines with a carburetor or central fuel injection system. 1. For the engine to operate efficiently, the temperature of the air entering the intake system must be maintained at a...
Every 58,000 km — Replace the fuel filter
Carburetor models 1. The fuel filter is installed in the outlet pipe of the fuel pump. To remove it, loosen the clamps (if any) and disconnect the filter from the hoses (see illustration). 26.1. Typical fuel filter...
Carburetor models 1. The fuel filter is installed in the outlet pipe of the fuel pump. To remove it, loosen the clamps (if any) and disconnect the filter from the hoses (see illustration). 26.1. Typical fuel filter...
Every 58,000 km — Replace transmission fluid and filter
Note: Checking the fluid level requires specialized Renault equipment, so please contact your Renault dealer. Avoid getting dirt into the transmission. 1. Transmission fluid should be changed when the transmission is...
Note: Checking the fluid level requires specialized Renault equipment, so please contact your Renault dealer. Avoid getting dirt into the transmission. 1. Transmission fluid should be changed when the transmission is...
Every 58,000 km — Check the rear brake shoe and drum
1. Block the front wheels, then jack up the rear of the vehicle and support it on axle stands. Remove the rear wheels. 2. You can quickly check the thickness of the brake pad lining through the opening in the caliper....
1. Block the front wheels, then jack up the rear of the vehicle and support it on axle stands. Remove the rear wheels. 2. You can quickly check the thickness of the brake pad lining through the opening in the caliper....
Every 58,000 km — check the handbrake adjustment
1. Make sure the handbrake holds the vehicle on the slope. If the mechanism is defective, it must be checked immediately as follows. Note: On models with rear drum brakes, if the handbrake is not functioning or adjusted...
1. Make sure the handbrake holds the vehicle on the slope. If the mechanism is defective, it must be checked immediately as follows. Note: On models with rear drum brakes, if the handbrake is not functioning or adjusted...
Every 58,000 km — Brake fluid change
1. The procedure is similar to bleeding the hydraulic system described in Section 9 , except that before starting work, you need to pump out the fluid from the brake hydraulic system reservoir using a clean siphon. 2....
1. The procedure is similar to bleeding the hydraulic system described in Section 9 , except that before starting work, you need to pump out the fluid from the brake hydraulic system reservoir using a clean siphon. 2....
Every 58,000 km — Check seat belts
1. Carefully inspect the belt fabric for cuts, severe abrasions or dirt. If the seat belt has a self-retractor, pull it out completely and inspect the fabric along its entire length. 2. Seat belts are designed to lock...
1. Carefully inspect the belt fabric for cuts, severe abrasions or dirt. If the seat belt has a self-retractor, pull it out completely and inspect the fabric along its entire length. 2. Seat belts are designed to lock...
Every 58,000 km — lubrication of hinges and locks
1. Lubricate the hood and door hinges, as well as all latches, locks and strike plates. At the same time, check the reliability of fastening and the functioning of all locks, adjust them if necessary ( see Section 11 )....
1. Lubricate the hood and door hinges, as well as all latches, locks and strike plates. At the same time, check the reliability of fastening and the functioning of all locks, adjust them if necessary ( see Section 11 )....
Every 58,000 km — Check the oil level in the manual transmission
1. Place the car on an inspection pit, overpass, or jack it up, but in any case, horizontally. 2. Unscrew the filler/inspection hole plug from the gearbox (see illustration). 34.2. Filler plug on the front of the...
1. Place the car on an inspection pit, overpass, or jack it up, but in any case, horizontally. 2. Unscrew the filler/inspection hole plug from the gearbox (see illustration). 34.2. Filler plug on the front of the...
Every 115,000 km — Replace the timing belt
Warning: If this step is neglected, the timing belt may break while the engine is running, causing significant damage to the engine. As a precaution, it is recommended to replace the timing belt after 58,000 km. The...
Warning: If this step is neglected, the timing belt may break while the engine is running, causing significant damage to the engine. As a precaution, it is recommended to replace the timing belt after 58,000 km. The...
Every 2 years, regardless of mileage — replace coolant
Draining the fluid Warning: Wait until the engine cools down. Avoid contact of antifreeze with your skin or painted surfaces of your vehicle. Wash away spilled drops immediately with plenty of water. 1. With the engine...
Draining the fluid Warning: Wait until the engine cools down. Avoid contact of antifreeze with your skin or painted surfaces of your vehicle. Wash away spilled drops immediately with plenty of water. 1. With the engine...
This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Other sections on other Renault models
➽ General information: Maintenance Renault Sandero 1 (2007-2012, petrol)
➽ General information: Maintenance Renault Kangoo 1 (1997-2007)
➽ General information: Maintenance Renault Laguna 2 (2001-2007)
➽ User manual: Maintenance and care Renault Megan 2 (2002-2009, petrol)
➽ General information: Maintenance Renault Fluence 1 (2009-2020, petrol)
➽ General information: Maintenance Renault Symbol 2 (2008-2013, petrol)
Link to this section in different formats
TEXTHTMLBB Code
- General information
- Maintenance
- Troubleshooting
- Power unit
- Petrol engines 1.1 l (C)
- Petrol engines 1.2 l (D)
- Petrol engines 1.2/1.4 l (E)
- Petrol engines 1.8 l (F)
- Diesel engines
- Overhaul of engines
- Cooling and heating
- Fuel system (carburetor)
- Central fuel injection
- Distributed fuel injection
- Fuel system (diesel)
- Starting and charging system
- Ignition system (transistor)
- Ignition system (electronic)
- Pre-heating of diesel engines
- Transmission
- Clutch
- Manual gearbox
- Automatic gearbox
- Drive shafts
- Chassis, running gear
- Brake system
- Car suspension
- Steering system
- Body and interior
- Exterior (external elements)
- Doors, locks and windows
- Electrical equipment
- Equipment and devices
- Electrical circuits