Engine oil pressure D7F engine At idle 0.8 bar. At 4000 rpm 3.5 bar. E7J engine At idle 1 bar. At 3000 rpm 3 bar. F8Q engine At 1000 rpm 1.2 bar. At 3000 rpm 3.5 bar.
Accessory Drive Belt Tension Required special tool Mot. 1273 Belt tension gauge. Fig 1.4a: A - Measuring block; B - Receiving unit with display; C - Connecting cable; D - Plate for control calibration. Principle of operation The measuring unit with...
Belt tension of the gas distribution mechanism Table 1.5 D7F engine 1. Remove retainer Mot. 1054 2. Install the extension sleeve of tool Mot. 1386 and tighten the crankshaft sprocket bolt. Pic. 1.8a 3. Install gauge Mot 1273 and use tool Mot. 1135-01 turn the idler...
Engine with camshaft pulley with marks Pic. 1.11a 1. Rotate the crankshaft of the engine, set the piston of cylinder No. 1 to the top dead center position. 4. Turn the crankshaft clockwise (from the gas distribution mechanism) to the first mark. 5. Adjust...
Engine with camshaft pulley without marks Fully Open Exhaust Valve Adjustment Procedure 1. Set cylinder #1 exhaust valve to full open position and adjust cylinder #3 exhaust valve and cylinder #4 exhaust valve clearances. 2. Proceed in the same way with the...
Tightening of bolts of fastening of a head of the block of cylinders 1. The cylinder head bolts are tightened using a goniometer disc for angle bolt tightening. To ensure proper tightening of the bolts, use a syringe to remove any oil that may be in the holes for the cylinder head...
Filling the cooling system The heater core valve is missing. The circulation of fluid through the heater core is constant, which improves the overall cooling of the engine. 1. Check the tightness of the drain plug or plugs. 2. Remove the plugs...
Removal of air from the cooling system 1. Let the engine run for 10 minutes at 2500 rpm before turning on the electric fan (electric fans) (time required for automatic degassing of the system). 2. Check that the fluid level is near the mark «Maxi»....
Checking the tightness of the cooling system Required special tool MS 554-01 Adapter for MS 554-05. MS 554-06 Adapter for MS 554-05. MS 554-07 Cooling system leak test kit. 1. Replace expansion tank valve with adapter MS 554-01. 2. Connect the MS 554-07 instrument...
Changing the oil in the gearbox Pic. 1.15 Refueling is carried out before oil starts to flow out of the drain hole. D7F engine Pic. 1.16: 1 - Drain plug; 2 - Filler plug. E7J engine Figure 1.17: 1 - Drain plug; 2 - Filler plug. F8Q engine Pic. 1.18: 1...
Tires and wheels Table 1.8 * For a fully laden vehicle when driving on a highway. ** Reinforced tire. Tightening torque for wheel nuts: 90 Nm. End runout of the rim: 1.2 mm. Tire pressures are for a fully loaded vehicle or motorway...
Brake service Table 1.9 * Brake drum: diameter at maximum allowable wear. Table 1.10 * Lead brake shoe. ** Driven brake shoe. *** With increased load capacity.
Brake force regulator Required special tool Fre. 244-03, Fre. 1085-01 Manometer for checking the performance of the brake force regulator. Roulette (used to measure the height of the control points under the car). These vehicles are equipped...
Power steering For topping up or refueling, use ELF RENAULT-MATIC D2 or MOBIL ATF 220 fluid. The normal fluid level is between the MIN and MAX marks on the wall of the filling tank. Pic. 1.22