Lower Body Control Points Dimensions H1 and H4 are measured along the wheel axis. Dimension H2 is measured between the bottom surface of the subframe (right under the wheel axle) and earth. Size H5 is measured along the axis of the silent block....
Lower arm Tightening torques, Nm Wheel bolts 90. Nut for fastening the axles of the lower arm to the subframe 90. Nut of a coupling bolt of fastening of a finger of a spherical support on a rotary knuckle 55. Stabilizer support...
Silent blocks — general information Replacement To ensure the exact location of the silent blocks in the lower arm, they must be replaced one by one. 1. Remove one of the worn bushings using a press and a piece of pipe with an outer diameter of 30 mm. 2....
Spherical bearing Removing Attention! If the boot is damaged, the entire ball joint must be replaced. 1. Place the vehicle on a two post lift. 2. Remove the front wheels. 3. Turn away nuts of fastening of the stabilizer on the bottom...
Hub bearing Required special tool Rou. 15-01 Protective tip of the drive shaft. Rou. 604-01 Hub retainer. T.Av 476 Ball joint puller. T.Av 1050-02. Hub puller. Tightening torques, Nm Drive shaft nut 280. Wheel bolts 90. Nut for...
Telescopic stand Necessary equipment Spring compression tool. Tightening torques, Nm Bolt of fastening of the bottom support of a telescopic rack 180. Nut for fastening the upper support cup of the spring on the rod of the shock...
Stabilizer transverse stability Required special tool Sus. 1413 Center stabilizer mount compressing tool. Sus. 1414 Stabilizer side support compression tool. Tightening torques, Nm Bolt of fastening of a bracket of a pillow of people of a support of...
Subframe — general information Required special tool Mot. 1040-01 Trolley for removal and installation of the power unit. T. Av. 476 Ball joint puller. Tightening torques, Nm Wheel bolts 90. Nut of fastening of a finger of a steering hinge 37. Bolt...
Rear axle with tubular beam Tightening torques, Nm Nut of fastening of a support of a beam of the back bridge 11. Wheel bolt 90. Bolt of fastening of the bottom support of the shock-absorber 85. Removing 1. Place the vehicle on a two post lift. 2....
Hub bearing Required special tool Emb. 880 Inertial puller. Rou. 943 Hub cap puller. Tightening torques, Nm Wheel bolts 90. Hub nut 175. Examination Check the axial clearance of the bearing by installing the indicator foot on the...
Shock absorber — general information Tightening torques, Nm Bolt of fastening of the top support of the shock-absorber 115. Bolt of fastening of the bottom support of the shock-absorber 85. Removing 1. On a car standing on our scaffolding, remove the bolt...
Stabilizer transverse stability Technical data Tightening torques, Nm Bolt of fastening of a support of the stabilizer 55. Removing 1. Remove mounting bolt 1. 2. Place the vehicle on a lift with wheels hanging freely. 3. On both sides of the car,...
Beam rods Tightening torques, Nm Nut of fastening of a support of a beam of the bridge 11. Bolt of fastening of a support of the stabilizer 55. Wheel bolt 90. Bolt of fastening of the bottom support of the shock-absorber 85....
Bearing rings Required special tool T. Ag. 960-02 Puller for bearing rings and bushings. T. Ag. 960-05 Tool for replacing needle bearings. Removing 1. The operation is performed after removing the rear axle and separating both beam...
Torsion — general information Technical data Required special tool Emb. 880 Inertial puller. Tightening torques, Nm Bolt of fastening of the top support of the shock-absorber 115. Bolt of fastening of the bottom support of the shock-absorber 85....
Silent blocks of torsion bars Removing 1. The operation is performed after removing the suspension arms and torsion bars. 2. Completely immerse the silent block in brake fluid to soften the rubber of the silent block. 3. Using a three-jaw puller,...
Four-torsion rear axle Required special tool Emb. 880 Inertial puller. The four-torsion rear axle consists of: two suspension arms connected by a segment of the L-shaped profile. Node 1 is one-piece; two stabilizers 3; two torsion bars 4;...