Share with friends:
Diesel engines of car Renault Clio 1
The compression and tightness of the Renault Clio 1 diesel engine connections are checked before disassembly. Next, the TDC of piston #1 is determined, the valve clearances are adjusted, and the toothed drive belt with sprockets and tensioner are removed. Next come the camshaft seals, camshaft with tappets, cylinder head, oil pan, and oil pump. Replacement of the crankshaft and intermediate shaft seals, engine mounts, oil cooler, and flywheel is described separately. A mechanic will understand the sequence of operations, and the owner will understand which components are affected by the diesel engine repair. If the engine is running rough, start with compression testing: it immediately indicates the condition of the cylinders. Before removing the belt, check the TDC marks.
Diesel engine specifications
Main characteristics Designation: Non-turbocharged engines - 1.9D models F8Q 620, F8Q 788* Turbocharged engines: Indirect injection - 1.9 dT models F8Q 784, F8Q 786* Direct injection - 1.9 dTi models F9Q 730, F9Q 734*...
Main characteristics Designation: Non-turbocharged engines - 1.9D models F8Q 620, F8Q 788* Turbocharged engines: Indirect injection - 1.9 dT models F8Q 784, F8Q 786* Direct injection - 1.9 dTi models F9Q 730, F9Q 734*...
General description — diesel engine repair in the engine compartment
About the Section This Section covers repair operations in the engine compartment on diesel engines. Procedures for engine removal and installation, and engine head/block rebuild can be found in Section 2F . Most of the...
About the Section This Section covers repair operations in the engine compartment on diesel engines. Procedures for engine removal and installation, and engine head/block rebuild can be found in Section 2F . Most of the...
Compression and leak testing of component connections — description
Compression check Note: Use a compression tester designed for diesel engines. 1. If the engine is not developing full power or is running rough, and if it is not related to the fuel system, a compression test can...
Compression check Note: Use a compression tester designed for diesel engines. 1. If the engine is not developing full power or is running rough, and if it is not related to the fuel system, a compression test can...
Top dead center (TDC) for piston #1 — location
Warning: The mentioned locating pins are intended exclusively to check the position of the crankshaft when performing various engine overhaul procedures. Not use them as locking tools to hold the crankshaft still while...
Warning: The mentioned locating pins are intended exclusively to check the position of the crankshaft when performing various engine overhaul procedures. Not use them as locking tools to hold the crankshaft still while...
Valve clearances — checking and adjusting
Note: This action is not included in the maintenance schedule. This should be done if noise is heard from the valve timing mechanism, or if it is suspected that the loss of power has occurred due to incorrect valve...
Note: This action is not included in the maintenance schedule. This should be done if noise is heard from the valve timing mechanism, or if it is suspected that the loss of power has occurred due to incorrect valve...
Toothed drive belt — removal, inspection and installation
Warning: If the timing belt breaks during operation, it can cause extensive engine damage. Replace the belt at the intervals specified in Specifications in Section 1 , or earlier if you have any doubts about its...
Warning: If the timing belt breaks during operation, it can cause extensive engine damage. Replace the belt at the intervals specified in Specifications in Section 1 , or earlier if you have any doubts about its...
Drive Belt Sprockets and Tensioner Mechanism — removal and installation
Note: F8Q 620 and early F8Q 784 engines are equipped with a toothed drive belt "HTD", while late F8Q and all F9Q engines are equipped with a belt with a different tooth profile "HTD2". Whenever the toothed drive belt is...
Note: F8Q 620 and early F8Q 784 engines are equipped with a toothed drive belt "HTD", while late F8Q and all F9Q engines are equipped with a belt with a different tooth profile "HTD2". Whenever the toothed drive belt is...
Camshaft seals — replacement
Oil seal on the drive belt side 1. Remove the camshaft sprocket as described in Chapter 6 . 2. Remove the woodruff key (where available) from the end of the camshaft. 3. Mark the installation depth of the old oil seal,...
Oil seal on the drive belt side 1. Remove the camshaft sprocket as described in Chapter 6 . 2. Remove the woodruff key (where available) from the end of the camshaft. 3. Mark the installation depth of the old oil seal,...
Camshaft and tappets — removal, inspection and installation
Note: A new drive belt side oil seal and a new valve cover gasket may be required during installation. The camshaft bearing caps will require sealant, and the bearing cap mounting bolts will require locking compound....
Note: A new drive belt side oil seal and a new valve cover gasket may be required during installation. The camshaft bearing caps will require sealant, and the bearing cap mounting bolts will require locking compound....
Cylinder head — removal, inspection and installation
Note: When installing, use a new head gasket and new cylinder head bolts, and a new valve cover gasket may also be required - see text. Removal 1. The following procedure describes the removal and installation of the...
Note: When installing, use a new head gasket and new cylinder head bolts, and a new valve cover gasket may also be required - see text. Removal 1. The following procedure describes the removal and installation of the...
Pallet — removal and installation
Note: When installing, use a new pan gasket or suitable sealant (where it is applied). Removal 1. Disconnect the negative cable from the battery ( see Section 5A ). Warning: If your car's radio is coded, make sure you...
Note: When installing, use a new pan gasket or suitable sealant (where it is applied). Removal 1. Disconnect the negative cable from the battery ( see Section 5A ). Warning: If your car's radio is coded, make sure you...
Oil pump — removal, inspection and installation
Intermediate shaft engines Removal 1. Remove the tray as described in Chapter 10 . 2. Unscrew the four pump mounting bolts and separate the pump from the cylinder block and drive gear (see illustration). 11.2. Removing...
Intermediate shaft engines Removal 1. Remove the tray as described in Chapter 10 . 2. Unscrew the four pump mounting bolts and separate the pump from the cylinder block and drive gear (see illustration). 11.2. Removing...
Crankshaft seals — replacement
Oil seal on the drive belt side 1. Remove the crankshaft sprocket as described in Chapter 6 . 2. Note the correct position of the old oil seal, then use a screwdriver to remove it from the casing. Do not damage the...
Oil seal on the drive belt side 1. Remove the crankshaft sprocket as described in Chapter 6 . 2. Note the correct position of the old oil seal, then use a screwdriver to remove it from the casing. Do not damage the...
Engine/Transmission Mounts — replacement
Inspection 1. Apply the handbrake, then jack up the front of the car and support it on axle stands where available, and remove the lower engine shield. 2. Visually inspect the rubber mounts on the two front and one rear...
Inspection 1. Apply the handbrake, then jack up the front of the car and support it on axle stands where available, and remove the lower engine shield. 2. Visually inspect the rubber mounts on the two front and one rear...
Oil radiator — removal and installation
Removal 1. Drain the cooling system as described in Section 1 . 2. Remove the oil filter ( see Section 1 ). 3. Loosen the clamps and disconnect the cooling system hoses from the engine oil cooler. 4. Unscrew the...
Removal 1. Drain the cooling system as described in Section 1 . 2. Remove the oil filter ( see Section 1 ). 3. Loosen the clamps and disconnect the cooling system hoses from the engine oil cooler. 4. Unscrew the...
Intermediate shaft seal — replacement
Note: This procedure only applies to engines with an intermediate shaft ( see Specifications ). 1. Remove the intermediate shaft sprocket as described in Chapter 6 . 2. Mark the installation depth of the oil seal, then...
Note: This procedure only applies to engines with an intermediate shaft ( see Specifications ). 1. Remove the intermediate shaft sprocket as described in Chapter 6 . 2. Mark the installation depth of the oil seal, then...
Flywheel — removal, inspection and installation
Proceed as described in Chapter 10 of Section 2A , but remember that on diesel models the gearbox can be removed separately as described in Section 7A - there is no need to remove the entire power unit to get to the...
Proceed as described in Chapter 10 of Section 2A , but remember that on diesel models the gearbox can be removed separately as described in Section 7A - there is no need to remove the entire power unit to get to the...
This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Other sections on other Renault models
➽ Power unit: Fuel system (diesel) Renault Scenic 1 (1996-2003)
➽ Power unit: Diesel engine (K9K) Renault Duster 1 (2009-2017)
➽ Power unit: Diesel engines 1.5 l Renault Logan 2 (2012-2020)
➽ Power unit: Diesel engines 1.9 l Renault Megane 1 (1995-2002)
Link to this section in different formats
TEXTHTMLBB Code
- General information
- Maintenance
- Troubleshooting
- Power unit
- Petrol engines 1.1 l (C)
- Petrol engines 1.2 l (D)
- Petrol engines 1.2/1.4 l (E)
- Petrol engines 1.8 l (F)
- Diesel engines
- Overhaul of engines
- Cooling and heating
- Fuel system (carburetor)
- Central fuel injection
- Distributed fuel injection
- Fuel system (diesel)
- Starting and charging system
- Ignition system (transistor)
- Ignition system (electronic)
- Pre-heating of diesel engines
- Transmission
- Clutch
- Manual gearbox
- Automatic gearbox
- Drive shafts
- Chassis, running gear
- Brake system
- Car suspension
- Steering system
- Body and interior
- Exterior (external elements)
- Doors, locks and windows
- Electrical equipment
- Equipment and devices
- Electrical circuits

