General information — air conditioning system 1. Left side deflector. 2. Grille blowing the left side window. 3. Lattices of an obduv of a windshield. 4. Central deflectors. 5. Nozzle blowing right side glass. 6. Right side deflector. 7. Hole for heating the legs...
Air conditioning system Heater The heater is powered by the engine cooling system, transferring the heat generated during the operation of the hotel's engine to the car interior. Air conditioning system 1. Compressor. 2. Condenser. 3....
Specification of air conditioning system Filling capacity of air conditioning systems depending on the type of engine The amount of refilled compressor oil when performing repairs on the air conditioning system and replacing various components Operation on the...
Necessary Precautions: Air Conditioning Operations Safety regulations Caution: These general precautions must be observed in all cases. 1. Wear protective gloves and goggles to eliminate any risk of frostbite. 2. Do not work with liquid refrigerant near open flames or...
Heating and air conditioning control Heating and air conditioning control panel Removal and installation of control of a heater and the conditioner 1. Unhook the central trim of the front panel. 2. Place the mixing chamber switch in the maximum heating...
Cabin air temperature sensor Removing the interior air temperature sensor 1. Remove the ceiling lining. 2. Remove adhesive tape (1). 3. Disconnect connector (2) and remove the interior air temperature sensor. 4. Installation is made in an order,...
Recirculation damper actuator Removal and installation Removing 1. Disconnect connector (1) recirculation damper actuator. 2. Unhook the recirculation damper actuator from the distribution block. Installation Installation is made in an order, the...
Air distribution damper actuator Removal and installation Removing 1. Disconnect connector (1) air distribution damper actuator. 2. Move bracket (2) from the air distribution damper drive. 3. Unhook the air distribution damper actuator from the...
Mixing chamber damper drive Removal and installation Removing 1. Disconnect connector (1) air distribution damper actuator. 2. Unhook the mixing chamber damper drive from the distribution block. Installation Installation is made in an order, the...
Ventilation system 1. Distribution block of the ventilation system.2. Left front leg area duct.3. Right front air duct leg area.4. Condensate drain pipe.
Distribution block Distribution block: 1. Distribution block. 2. Fan assembly. 3. Lower cabin filter. 4. Cabin filter cover. 5. Cable drive mixing damper. 6. Cable drive damper air distribution. 7. Heater resistor. 8. Heater core pipe...
Front side air vents Removal and installation of forward lateral air ducts 1. Remove the dashboard. 2. Remove the front side air duct from the appropriate side of the vehicle. 3. Installation is made in an order, the return to removal.
Middle air ducts in the leg area Removal and installation Removal, left side 1. Block the airbag processor. 2. Disconnect the negative battery terminal. 3. Remove the driver's airbag. 4. Remove the steering wheel. 5. Remove the steering column...
Cabin filter Cabin filter replacement 1. Remove the sound deadening material under the dashboard from the clip and set aside. Note: Foreign bodies (leaves, insects, etc.) usually accumulate on the cabin filter. When removing the...
Fan assembly Removal and installation of the fan assembly Caution: Do not use near pyrotechnic devices (seat belt pretensioners and airbags) heat sources and open flames - pyrotechnic devices may work. 1. Block the airbag processor....
Heater core Removal and installation of the heater core Removing the heater core 1. Clamp the heater core hoses with clamps (Ms. 583). 2. Raise the edge of the floor mat. 3. Before removal, mark the position of the rack relative to...
Air conditioning system 1. Capacitor. 2. Air conditioning compressor. 3. Seal the refrigerant piping. 4. Seal the refrigerant piping. 5. Seal the refrigerant piping. 6. Connecting pipeline condenser-intermediate pipeline. 7. Pressure sensor....
Checking the air conditioning system Note: To test the air conditioning system, you will need a dual temperature gauge. 1. Check the functionality of the measuring device (see the operating instructions supplied with the device). 2. Set the device to the°C...
Automotive capacitor Removal and installation of the condenser Removing the capacitor 1. Place the vehicle on a two post lift. 2. Using a special station, remove the refrigerant from the air conditioning system. 3. Remove the front bumper...
Expansion valve Removal and installation Removing 1. Disconnect the negative battery terminal. 2. Using a special station, remove the refrigerant from the air conditioning system. 3. Loosen the connecting pipe bracket bolt "expansion...
Cleaning the evaporator Attention: Do not spray cleaning agent through the air intake, as this may damage the fan. 1. Place the vehicle on a two post lift. 2. Remove cabin filter (see relevant section earlier in this chapter). 3. Using the...
Evaporator sensor Removing and installing the evaporator sensor Removing the evaporator sensor 1. Remove the soundproofing. 2. Remove the evaporator sensor (1), by turning it a quarter of a turn clockwise. 3. Cut the wires to the...
Refrigerant pressure sensor Removal and installation of the coolant pressure sensor 1. Place the vehicle on a two post lift. 2. Using a special station, remove the refrigerant from the air conditioning system. 3. Remove the front bumper from the...