Electrical equipment and appliances Renault Logan 1

Design features of on-board electrical equipment
The car uses direct current electrical equipment with a nominal voltage of 12 V. The car's electrical equipment is made according to a single-wire scheme: the negative terminals of the sources and consumers of...

Diagnostics of faults of on-board electrical equipment
A typical electrical circuit may include a main electrical component, various switches, relays, electric motors, fuses, fuse links or circuit breakers associated with that component, wiring and connectors used to...

Location of fuses, fuse links and relays and their replacement
Most of the power circuits of the car's electrical equipment are protected by fuses. Headlights, fan motors, fuel pump and other powerful consumers are connected via relays. Fuses and relays are installed in mounting...

Features of the ignition switch design
The ignition switch with a mechanical locking device and an electrical contact part is located on the right side of the steering column under the steering wheel. The electrical contact part of the switch and the locking...

Checking the ignition switch (lock)
The ignition switch (lock) is checked for correct contact closure in different key positions, as well as the operation of the anti-theft device. To ensure correct contact closure, use a tester in the circuit...

Removal and installation the ignition switch (lock)
The ignition switch (lock) is installed on the steering column in the housing and secured with one bolt. You will need: TORX T20 key, flat-blade screwdriver. 1. Disconnect the wire from the negative terminal of the...

Checking and replacing steering column switches
You will need: TORX T20 key, Phillips-head screwdriver, tester. 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the steering column cover, see. "Removing and installing the ignition switch...

Removal and installation the horn
You will need: a 10 mm wrench, a 13 mm socket head. 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the lower part of the left engine splash guard (see "Removal and installation of mudguards...

Replacing Windshield Wiper Blades
1. Raise the wiper arm. 2. Press the lock... 3. ...and slide the brush along the wiper arm. 4. Remove the brush. 5. Install the parts in the reverse order of removal.

Windshield wiper gear motor replacement
Disassembling the wiper gear motor is not practical, as spare parts are not supplied for it. Only the complete gear motor can be replaced. You will need: keys "10", "13" and "24", a screwdriver with a flat blade. 1....

Removal and installation the windshield washer
1. Disconnect the wire from the negative terminal of the battery. 2. Remove the right side of the air intake box grille (see "Removing and installing the air intake box grille" ). 3. Disconnect the wiring harness...

Removal and installation of the electric motor of the radiator fan of the engine cooling system
You will need a flat-blade screwdriver. 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the electric fan of the engine cooling system (see "Removal and installation of the electric fan of the...

Electrically heated rear window
The rear window heating element consists of horizontal conductive strips connected on both sides by vertical buses. One bus is connected to the "+" of the on-board electrical system, the other - to the "ground" of the...

Removal and installation the cigarette lighter socket
You will need a flat-blade screwdriver. 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the cigarette lighter from the socket. 3. Press the fasteners with a screwdriver... 4. ...and remove...

Features of the instrument cluster design
All the vehicle's control and measuring devices are combined into a cluster of devices. It includes a speedometer, an on-board computer display, an electronic tachometer, control and signal lamps, and backlight lamps....

Removal and installation the instrument cluster
You will need a TORX T20 key. 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the upper steering column cover, see. "Removing and installing the ignition switch (lock)" . 3. Remove the two...

Features of the immobilizer design
An immobilizer is installed on Renault Logan cars – an electronic device designed to prevent unauthorized engine starting by breaking the electrical circuits of the engine control system. The immobilizer consists of a...

Replacing the instrument panel switches
You will need a flat-blade screwdriver. 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the radio socket cover... 3. ...and disconnect the wiring harness connectors and the antenna wire from...

Removal and installation speakers of the acoustic system
You will need: TORX T20 key, flat-head and Phillips-head screwdrivers. 1. Use a screwdriver to pry up and remove the front door speaker grille, overcoming the force of the clamps. 2. Remove the four speaker mounting...

Removal and installation the antenna
1. Unscrew the antenna from the bracket by turning it counterclockwise... 2. ...and take it off. 3. Install the parts in the reverse order of removal.

Replacing the oil pressure warning light sensor
The oil pressure warning light sensor is installed at the rear of the cylinder block on the right side (next to the engine number). You will need a 22 mm wrench. 1. Disconnect the wire from the negative terminal of the...

Replacing the fuel level indicator sensor
The fuel level indicator sensor is located in the fuel pump module. You will need a flat-blade screwdriver. 1. Reduce the pressure in the fuel system (see "Lower pressure in the fuel system" ). 2. Disconnect the wire...

Replacing the reverse light switch
The reversing light switch is installed at the rear of the gearbox housing near the left front wheel drive. You will need: a 24 mm wrench, a flat-blade screwdriver. 1. Disconnect the wire from the negative terminal of...

Replacement and adjustment of the brake light switch
The brake light switch is mounted on the pedal assembly bracket. 1. Disconnect the wire from the negative terminal of the battery. 2. Squeeze the clips and disconnect the wiring harness connector from the brake light...

Replacing the parking brake indicator light switch
You will need a Phillips-head screwdriver. 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the parking brake lever (see "Removing and installing the parking brake drive lever" ). Note: The...

Replacing the interior light switches
You will need a flat-blade screwdriver. 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the protective cap from the switch. 3. Use a screwdriver to press the fasteners and remove the switch...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share with friends:

Other sections on other Renault models

➽ Electrical equipment: Equipment and devices Renault Clio 1 (1990-1998)
➽ Electrical equipment: Equipment and instruments Renault Espace III (1996-2002)
➽ Electrical equipment: Equipment and devices Renault Megan 2 (2002-2009, petrol)
➽ Electrical equipment: Equipment and devices Renault Fluence 1 (2009-2020, petrol)
➽ Electrical equipment: Equipment and devices Renault Scenic 1 (1996-2003)
➽ Electrical equipment: Equipment and devices Renault Symbol 1 (1999-2008, petrol)

Link to this section in different formats

TEXTHTMLBB Code