Specifications of the brake system Note. When replacing one of the elements of the vehicle's brake system, always mark the pipelines before removing them so that they can be installed in their original places. * Brake discs cannot be sanded. In case of...
Brake fluid — topping up and replacing Intervals for changing brake fluid The technology of our brakes and in particular disc brakes (hollow pistons transfer little heat, little fluid in the cylinder, floating calipers, eliminating the need for a relatively...
Trajectory stabilization system MK 60 Note. An electronic trajectory stabilization system complements the ABS. The electronic trajectory stabilization system consists of the following elements: brake force booster. including the emergency brake booster, the...
Removal and installation of the ABS computer Removing Note. To remove the ECU, the ABS valve body is not required from the vehicle. Remove the two mounting bolts on the hydraulic pump and the ECU. Attention! During removal, hydraulic pump A must be pressed against...
Steering angle sensor The electronic stability control system uses the signal from the steering angle sensor to calculate the trajectory chosen by the driver. This information is regarded as a driver's command. The steering wheel angle...
Steering wheel angle sensor calibration Set the card in the reader to the 2nd fixed position. Turn the steering wheel at least. than 4°. which corresponds to approximately 1 cm on the circumference of the steering wheel rim. As a result, the sensor becomes...
Removal and installation of wheel sensors Removing Use a flathead screwdriver to pry out the sensor retaining plate at point G to release the sensor. Pull on the sensor to remove it. Disconnect sensors: in front of the sensor holders; rear in the wheel arch...
Removal and installation of the pressure sensor Note. The sensor sends information about the pressure in the brake master cylinder to the ECU. Removing Place the car on a lift. Install a pressurizer on the brake pedal to prevent leakage of brake fluid. Attention!...
Bleeding the brake system Note. The valve body is pre-filled with brake fluid. The bleeding procedure is applied after removing the following items: hydroblock: master brake cylinder; pipeline (between hydraulic block and brake master cylinder)....
Automatic parking brake List and location of system elements The automatic parking brake system includes: handle 1, which replaces the parking brake lever. The handle is located on the dashboard, next to the steering wheel; clutch pedal travel...
Fittings and pipelines of a brake hydraulic drive Connection of pipelines between the brake master cylinder, floating brake calipers, brake force regulator and hydraulic unit is carried out by means of threaded fittings with metric threads. Therefore, it is so...
Removal and installation of front brake pads Removing Remove: clamping spring from the front of the brake caliper; brake hose shock absorber; two protective caps guide pins; two guide pin bolts. Hang the brake caliper and remove the brake pads. Installation...
Removal and installation of brake calipers Removing Place the car on a two post lift. Remove the front wheels. Install a pressurizer on the brake pedal to prevent leakage of brake fluid. Remove: clamping spring from the front of the bracket: a bracket that...
Removal and installation of a brake disk Removing Place the car on a two post lift. Remove: front wheels; brake caliper (see brake pad removal method). Hang the bracket to the body. Attention! Attach the brake hose and ABS sensor wires securely. if they are...
Removal and installation of a rotary fist Removing Place the car on a two post lift. Remove the front wheels. Remove the ABS sensor from the steering knuckle. Remove brake caliper (see Brake pad removal method ). Hang the bracket to the body. Remove the hub...
Removal and installation of rear brake pads Removing Remove both rear wheels. Disconnect the parking brake cables from the rear suspension beam. Remove: clamping spring pads; two plugs of guide pins; two guide pin bolts. Hang the brake caliper to the body and...
Removal and installation of brackets of brake mechanisms Removing Remove wheels. Install a pressurizer on the brake pedal to prevent leakage of brake fluid. Disconnect the parking brake cables from the rear suspension. Release the brake pipe fitting on the caliper. Remove:...
Removal and installation of the rear wheel hub assembly — brake disc Removing Remove: wheels; brake calipers (see brake pad operations); two bolts for fastening the guide pads; hub cap; hub nut (using a 36mm socket); rear wheel hub assembly - brake disc. Installation The installation is...
Removal and installation of the main brake cylinder Place the car on a lift. Attention! Take measures to collect brake fluid to prevent damage to parts and the body in the area of \u200b\u200bthe elements of the brake system. Removing Remove: intake silencer; expansion...
Vacuum brake booster (MCP JH3-JR5) — withdrawal Place the car on a lift. Attention! Take measures to collect brake fluid to prevent damage to parts and the body in the area of \u200b\u200bthe elements of the brake system. Remove: master brake cylinder (see...
Vacuum brake booster (Automatic transmission DPO) — withdrawal Place the car on a lift. Attention! Take measures to collect brake fluid to prevent damage to parts and the body in the area of \u200b\u200bthe elements of the brake system. Remove: master brake cylinder (see...
Vacuum brake booster (MCP RK6) — withdrawal Place the car on a lift. Attention! Take measures to collect brake fluid to prevent damage to parts and the body in the area of \u200b\u200bthe elements of the brake system. Remove: air pipe; air filter housing; fuse...
Vacuum brake booster (Automatic transmission SU1) — withdrawal Place the car on a lift. Attention! Take measures to collect brake fluid to prevent damage to parts and the body in the area of \u200b\u200bthe elements of the brake system. Remove: air pipes; intake manifold; air...
Installing a vacuum brake booster Before remounting, check: distance L = 165.5 mm (left hand drive vehicles) |_= 122 mm (right hand drive vehicles). The size is adjusted by pusher C. When installing the vacuum booster and brake master cylinder, proceed...
Checking the tightness of the vacuum brake booster When checking the tightness of the vacuum brake booster, make sure the joint between the vacuum booster and the master brake cylinder is tight. If a leak is found, replace O-ring A. Checking the tightness of the vacuum...
Air filter — check valve Air filter replacement The vacuum booster does not need to be removed to replace the air filter F. Using a screwdriver or a metal hook, remove the dirty filter F, which is located under the pedal assembly. Cut a new...
Emergency braking system Note. The emergency braking system complements the ABS. Description Two types of technologies allow for increased braking force during emergency braking. One is based on the use of electronic components (electronic...
Removal and installation of the diaphragm movement sensor Removing Disconnect the wiring harness from the sensor. Use a small screwdriver to loosen the sensor clamp and remove it. Installation Attention! Before installing the diaphragm displacement sensor, be sure to replace...
Removing and installing the brake pedal stroke sensor Removing On the brake pedal bracket: Disconnect the brake pedal travel sensor wire. Turn a quarter turn counterclockwise. Remove the brake pedal travel sensor. Installation The sensor is adjusted automatically depending...
Removal, installation and adjustment of the parking brake lever Withdrawal (inside the car) Remove: corrugated cover of the gear lever; corrugated cover of the parking brake lever; Renault card reader; two front center dash screws. Remove the two rear center console screws....
Removal and installation of brake hoses Precautions when removing and installing brake caliper or brake hose For safety reasons and to avoid twisting of the brake hoses, as well as the possibility of them touching the suspension parts, the following work...
Brake system diagnostics Malfunctions that appear on the brake pedal Malfunctions manifested in the behavior of the car on the road
Diagnostics of the ABS system The ABS performs the following functions on this vehicle: ABS (anti-lock braking system). The main function of the ABS is electronic brake force distribution (Electronic brake force distributor) between the front and...
Replacement of elements of the ECU system ABS ECU Replacement When replacing the computer, proceed as follows: turn off the ignition; replace the computer; enter VIN using command VP001; set the speed measurement index with command VP007; adjust vehicle...
ECU configuration and programming Settings VP001: VIN entry. This command allows you to manually enter the VIN. car in the ECU. This command is used every time the computer is replaced. VIN (VF.) inscribed on the nameplate on the pillar of the right...