Removal and installation of the cylinder of the lock of a forward door Removing Remove: door lock cylinder cover A; plug, then unscrew screw 1 (torx T 20). without taking it out. Remove lock cylinder 2. Note. It is possible to remove the lock cylinder cover A without removing the cylinder.
Removal and installation of the external door handle Removing Remove the plug. Remove screw 1 (torx T20), without removing it, then remove the door lock cylinder 2. Remove handle 3, then 4. Installation Check that door handle gasket A is installed correctly.
Door locks — removal and installation Removing the front door lock After removing the trim panel and the outer handle, remove the three mounting bolts A (torx T30). Lightly press the two stoppers of assembly B. Remove the lock and assembly through the door...
Removal and installation of windows of forward doors Removing After removing the inner lining, remove the two glass mounting clips A, disconnect the glass from the axes of the power window slider. Raise the glass manually and secure it with protective tape. Remove the...
Removal and installation of windows of back doors Withdrawal (power window regulator) After removing the inner lining, remove the glass holder A. Disconnect glass from an axis of a slider of a window regulator. Raise the glass manually. Secure it with safety tape....
Lock drive and tailgate lock Note. In the event of a malfunction, the tailgate can be opened manually. Using a small screwdriver, press tab A from inside the vehicle. Removing After removing the upholstery of the tailgate, remove the protective...
Front door — adjustment Note. The method describes only the points. used for adjustment. The front doors of the station wagon do not differ from the front doors of the basic version. Note. Access to the details of fastening the hinges on the...
Tailgate — adjustment Note. The procedure describes only the points used in the adjustment. The rear doors of the station wagon type have special features. but the method of their installation does not differ from the method of installation...
Filler manhole cover — removal and installation The replacement of this part is related to the replacement of the rear fender panel after a possible rear side impact. Contents of delivery Part Supplied Separately (primed). Removing Press both spring clips A with your...
Hood adjustment Replacing this part is the main operation in case of a possible frontal impact. This element is removable and made of aluminum. Note. Since the removal and installation operations are not particularly difficult, only...
Tailgate and tailgate Replacing this part is the main operation in a possible rear impact. This item is removable. The door is made of a composite material based on polyester resin. Note. Only adjustment operations for both modifications are...
Removal and installation of the sunroof Removing After removing the headliner and folding the backrests of all seats, remove the twelve mounting bolts A. Disconnect the four drain pipes B. Together with an assistant: remove the four bolts securing to the...
Removal and installation of the sunroof drive motor Removing Remove the sunroof control unit. Remove the dome light. Disconnect the two motor connectors. key (hexagon 4 mm) turn bolt A to close the sliding panel (if it is open). Remove the three Torx bolts (T20), then...
Removal and installation of the mobile panel Removing After removing the two covers of the mechanism, remove the four mounting bolts A (M5 head BTR4). Pay attention to inserts B. After installing the sunroof, proceed to adjust the panel. The gaps between the panel...
Removal and installation of an upholstery of the hatch Removing After removal: roof hatch gaskets; handrails (using the Sag tool. 1597); upper facings of the middle pillar; side panel facings; two rear roof lining clips. Open the sliding panel. Using a long flathead...
Removal and installation of a windshield Removing After removing the wiper arms and the two air intake grilles, remove the A-pillar trims. Remove top trim B holding gaskets C. Remove: sun visors and their brackets; windshield pillar linings; interior rearview...
Removal and installation of glass of a forward door Removing After removing the inner lining. remove the inner sealing profiled strip of glass A, two glass holders B. Remove the glass from the axes of the glass lift slider. Installation Check the installation of the...
Removal and installation of glass of a back door Removing After removing the inner lining, remove the inner glass sealing strip A and the glass holder B. Remove the glass from the axis of the power window drive slider Lower the glass to the bottom of the door frame...
Removal and installation of back glass Removing After removal: rear aileron; wiper arm (using the E1e tool. 1552); upholstery of the tailgate; remove the side covers. Disconnect the satellite dish connector A, then remove it B. Disconnect the defroster wire...
Removal and installation of the back opening glass (station wagon) Removing Detach access hatch A. Disconnect the glass defroster wire connector. Remove: upper brake light cover B; decorative trim of the lock C. Remove the two bolts securing the third upper brake light D. Disconnect a...