Duster Fluence Kangoo Laguna Logan Megane Sandero Scenic Symbol Clio Other

Car clutch repair Renault Laguna 2

General information about the clutch
The clutch is located between the engine and the gearbox and is designed to disconnect and connect the flywheel mounted on the engine crankshaft and the input shaft of the gearbox. On vehicles equipped with a manual...

Bleeding the hydraulic clutch release drive
Caution! Be careful not to spill clutch fluid on painted surfaces. If this happens, wash off the fluid immediately with water. Note: Do not mix different brands of clutch fluid. Do not reuse drained clutch fluid. Any...

Adjusting the free travel of the clutch pedal
Disconnect the supply line between the reservoir and the clutch master cylinder. Close the opening of the tank. Add a small amount of certified brake fluid to the syringe. Insert the syringe into the feed line between...

Adjusting the clutch drive
Adjust the stroke of the clutch cable with the nut on the end on the gearbox side. Loosen the locknut. Adjust the clutch cable stroke by loosening or tightening the nut. Tighten the lock nut to the specified torque (8...

Removal and installation the clutch cable
Removal In the engine compartment, disconnect the cable from the clutch release fork. Press the pedal to retract the cable into the passenger compartment. Remove the cable from the pedal socket by lifting the pedal and...

Removal and installation the clutch pedal
Removal Disconnect the wires from the battery terminals, starting with the negative terminal. Remove the left lower shroud and air duct. Remove the gray start sensor by turning it a quarter turn. Disconnect the wiring...

Removal, adjusting and installing the clutch pedal travel sensor
Caution: Handle the clutch pedal travel sensor with care. The rod may only be moved when adjusting the X dimension. Disconnect the clutch pedal travel sensor connector. Turn the clutch pedal travel sensor 1/4 turn...

Removal and installation the clutch hydraulic line
Removal Place the car on a lift. Disconnect the battery. Remove the top engine cover and air intake grille. Remove the two mounting bolts and the air filter access panel, as well as the mounting bolts for the air intake...

Clutch Identification Data
Clutch housing with pressure plate assembly and driven clutch disc (engines and K4M) Outside diameter of driven disk: 200 mm. Driven disc thickness: 6.9 mm. Number of splines: 26. Colour of marking of springs 1 and 2 of...

Removal and installation the casing and driven clutch disc (K4M engine)
Removal Remove the gearbox. Install the latch (Mot. 582-01). Loosen the clutch housing mounting bolts. Remove the clutch slave disc. Use a vacuum cleaner or a clean cloth to remove dust from the clutch housing. Do not...

Removal and installation the clutch housing and driven disc (F4R engine)
Removal Remove the gearbox. Install the latch (Mot. 582-01). Loosen the clutch housing mounting bolts. Remove the clutch slave disc. Use a vacuum cleaner or a clean cloth to remove dust from the clutch housing. Do not...

Removal and installation the clutch flywheel
Removal Remove the gearbox. Remove the clutch housing with the pressure plate assembly. Install the latch (Mot. 582-01). Loosen the flywheel mounting bolts, remove the flywheel and retainer (Mot. 582-01). Install the...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share with friends:

Other sections on other Renault models

➽ Transmission: Clutch Renault Clio 1 (1990-1998)
➽ Transmission: Clutch Renault Kangoo 1 (1997-2007)
➽ Transmission: Clutch Renault Megane 1 (1995-2002)
➽ Transmission: Clutch Renault Sandero 1 (2007-2012, petrol)
➽ Transmission: Clutch Renault Duster 1 (2009-2017)
➽ Transmission: Clutch Renault 19 (1988-1996)

Link to this section in different formats

TEXTHTMLBB Code