Clutch — general information The clutch is located between the engine and gearbox and is designed to disconnect and connect the flywheel mounted on the engine crankshaft and the gearbox input shaft. On vehicles equipped with a manual transmission,...
Clutch Diagnostics Attention. For all engine types, use a clutch compression tool when installing the clutch assembly. clutch vibration (jerks when touching) slippage (slippage) clutch Clutch pedal is hard to move clutch noise (resistance...
Pumping the clutch hydraulic drive Attention. Use only new, non-emulsified brake fluid, do not allow hydraulic circuit contamination. Attach transparent tube (6) on the bleeder valve (in the zone «f»). Dip the end of the tube into a container of brake...
Clutch drive adjustment Adjust the clutch cable travel with the nut on the transmission side end. Loosen the locknut. Adjust the clutch cable travel by loosening or tightening the nut. Torque tighten (8 Nm) locknut. Adjustment check Using a...
Clutch cable In the engine compartment, disconnect the cable from the clutch release fork. Step on the pedal to retract the cable into the passenger compartment. Remove cable from pedal socket (1), while lifting the pedal and...
Clutch pedal and clutch pedal travel sensors Switch off the ignition. Disconnect the battery ( see Battery: Removal and installation ). Remove the instrument panel lower trim and the UCH (1). Clutch end travel sensor Disconnect connector (2) from the pedal travel...
Clutch hydraulic pipeline Place the car on a lift. Disconnect the battery. Remove the engine top cover and air intake grille. Remove the air filter housing. Remove the brake fluid from the reservoir with a syringe so that its level is below the...
Clutch Master Cylinder Remove: battery; battery shelf; air filter housing; a plug from the nozzle for removing air. Connect a clear tubing to the bleeder fitting by dropping the other end into an empty vessel above the bleeder bleeder. Raise...
Driven disc and clutch release bearing Driven disk Remove the manual gearbox. Lock the flywheel with a latch (Mot. 1677) (1). Remove: bolts (2) fixing the clutch cover with the pressure plate assembly; node «pressure plate - driven disc». Clean with cleaner:...
Flywheel — general information Remove the gearbox. Remove the clutch cover with pressure plate assembly. Install retainer (Mot. 582-01) (1). Remove the flywheel mounting bolts, remove the flywheel and retainer (Mot. 582-01). Install retainer (Mot....
Replacing the differential seal Place the car on a lift. Disconnect the wires from the battery terminals, starting with the negative terminal. Remove the engine undertray. Drain the gearbox oil. Remove: wheel; mudguard; hub nut; tie rod end ball...
Drive mechanism General information Drive shafts transmit torque from the engine, gearbox and differential to the front wheels. In the gearbox housing, the drive shafts are splined to the side gears of the differential. Fixing the...
Left front wheel drive shaft (vehicles with automatic transmission) Place the car on a lift. Remove: engine undertray protection; left front wheel. Install an oil collection container. Disconnect: wiring harness (1) wheel speed sensor; brake hose (2). Remove: fastening bolt (3) brake...
Right front wheel drive shaft (cars with manual gearbox) Place the car on a lift. Remove: engine crankcase mounting bolts; engine undertray protection; left front wheel. Drain the oil from the manual transmission. Disconnect the wiring from the wheel speed sensor at the point...
Drive shaft repair Cover of the internal hinge of a shaft of a drive of a forward wheel Front wheel drive shaft inner hinge cover: 1 - protective ring; 2 — wheel drive shaft; 3 - ball bearing; 4 - hinge body; 5 - tripod hinge; 6 -...
Cover of the external hinge of a shaft of a drive of a forward wheel Cover of the external hinge of a shaft of a drive of a forward wheel: 1 - large clamp; 2 — a small coupling collar; 3 - protective cover; 4 - clip; 5 - hinge body; 6 - separators; 7 - wheel drive shaft; 8 - balls; 9 -...