Exterior (external elements) of the car Renault Laguna 2

Location of electronic units on the car
Note: When carrying out welding work in a vehicle, it is necessary to: disconnect the battery; remove or disconnect electrical devices (ECU etc), which are located near the work area and which may be damaged due to...

Features of parts with very high elastic limit
The body frame of the Laguna II cars is partly made of components with a very high elastic limit. As their name suggests, these body parts are very strong and flexible. They are stamped using a special technology. When...

Gaps of opening body elements
Gaps of opening elements of the "Hatchback" body

Removal and installation the front bumper
Front Bumper Components Removal Remove: three bolts and lower bracket A of the lower elements of the front wing protection; engine oil pan protection mounting bolts B (M6 head 10). Unscrew the mounting bolts C (Torx...

Removal and installation the rear bumper (hatchback)
Rear Bumper Components (Hatchback) Removal Remove the tail lights. Unscrew the upper mounting bolts A (Torx T20). Remove the three lower holders B (plastic rivets). Unscrew the mounting bolts C (Torx T20). Unscrew the...

Removal and installation the rear bumper (station wagon)
Rear Bumper Components (-station wagon-) Removal Remove the three bolts securing the rear lights A. Disconnect the connectors, then remove the lights. Unscrew the mounting bolts B. Remove the two C holders (plastic...

Side protective pads
Removal the front door protective trim Remove the turn signal repeater from the door using a small flat-head screwdriver. Disconnect the connector. Remove the plug, then use a screwdriver (Torx T30) to press on the...

Removal and installation the radiator grille
Removal Remove the four A holders (plastic rivets). Press the center holder using the cap wrench (on 17) as a lever to remove the radiator grille by moving up.

Removal and installation the air intake niche grille
Removal the left air intake grille After removing the wiper arms, remove: gasket of the air intake niche wall A; three holders B (plastic rivets). Disconnect the grille at point 1, then at point 2. Proceed in the same...

Decorative trim for the lower part of the tailgate (station wagon)
Removal the overlay Remove the central mounting bolt A (Torx T20). Insert the rear view mirror glass removal tool (Cag. 1363) between the tailgate and the trim panel. Press the lever (on the handle of the tool) at point...

Removal and installation the rear aileron
Removal Remove: four mounting bolts A (Mb head for 10); aileron. Installation Apply sealing mastic (Stock No.77.11.170.230) around the hole of the B holder. Features of spare parts The tailgate parts are supplied with...

Removal and installation the rear aileron with a station wagon body
Removal After removing the rear window, remove: the liquid supply tube to the windshield washer nozzle A; two mounting bolts B. Remove the aileron.

Removal and installation the outside rearview mirror
Removal (using the device Sag. 1363) Remove the inner cover A, fix it at point B. Disconnect connector C. Remove the three mounting bolts D. Remove the rear view mirror together with the foam seal. Installation Before...

Removal and installation the glass of the outside rearview mirror
Removal Insert the tool Sag. 1363. using the edge of the plastic housing of the rear view mirror as a support, then press as shown in the figure above. Removal glass equipped with anti-glare system Using the handrail...

Removal and installation the outer decorative trim of the front door pillar
Removal Insert a mastic removal knife (not sharp) between the door frame and the trim. Using a hair dryer, peel off the decorative strip at point 1.

Removal and installation the outer decorative trim of the rear door pillar
Removal Remove the front door pillar gasket holder A. Insert a mastic removal knife (not sharp) between the door pillars and the trim strips 1. Using a hair dryer, peel off the decorative strip at point 1, then remove...

Removal and installation of decorative trim for car gutters (station wagon)
Removal Using the handrail removal tool (Cag. 1597), the end of which is wrapped with protective tape, detach the decorative cover A, starting from the rear.

Removal and installation roof rack rails
Removal With the help of the device Sag. 1597 (with the end wrapped in safety tape), remove the front and rear retaining covers. Remove the mounting bolts A, then B, and the roof rack guides. Remove the rear roof trim...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share with friends:

Other sections on other Renault models

➽ Body and interior: Exterior and interior Renault Kangoo 1 (1997-2007)
➽ Body and interior: Exterior (external elements) Renault Clio 1 (1990-1998)
➽ Body and interior: Exterior (external elements) Renault Symbol 1 (1999-2008, petrol)
➽ Body and interior: Exterior (external elements) Renault Sandero 1 (2007-2012, petrol)
➽ Body and interior: Exterior (external elements) Renault Logan 2 (2012-2020)
➽ Body and interior: Exterior (external elements) Renault Espace III (1996-2002)

Link to this section in different formats

TEXTHTMLBB Code