Exterior (external elements) of the car Renault Duster 1

Front side door
Tightening torques Front side door hinge mounting nuts 28 Nm Bolts and nuts for fastening the hinges of the front pillar 28 Nm Removing the front door can be done in two ways: without loops, with loops. Note: The front...

Rear side door
Tightening torques Rear side door hinge mounting nuts 28 Nm Nuts and bolts for fastening the hinges of the middle pillar 28 Nm Removing the rear door can be done in two ways: without loops, with loops. Removal Remove:...

Fuel filler cap manhole cover
Removal Remove: screws (1), fuel tank filler cap. Installation Lubricate the fuel filler cap joints with a general purpose grease. Installation is carried out in the reverse order of removal.

Side door frame seal
Removal Remove the decorative cover screw (1). Remove the trim at point (2). Remove the decorative cover (2). Remove the door frame seal (3). Remove the door frame seal (4). Installation Installation is carried out in...

Hood — removal, installation and adjustment
Removal Disconnect the hoses from the windshield washer jets at point (1). Remove the windshield washer fluid supply pipe clamp at point (2). Removing by unscrewing the hood mounting bolts Remove the hood strut. Remove:...

Tailgate — Removal and Installation
Removal without loops Remove the rear door trim. Disconnect the connectors: rear window wiper motor, high brake light, trunk door lock, rear window heating element, license plate lights. Remove: tailgate wiring harness,...

Outer part of the rear opening element
1 - Hood 2 - Front bumper 3 - Hood hinge 4 - Front wing 5 - Side bracket with spring retainer for front bumper 6 - Front bumper side bracket spring retainer rivet 7 - Front part of the threshold panel extension 8 -...

Hood lock drive cable
Removal Remove the hood lock actuator handle (1). Installation Installation is carried out in the reverse order of removal.

Hood lock — removal and installation
Tightening torques: Bonnet mounting nuts - 21 Nm. Removal Remove: front bumper, air deflector. Unscrew the nuts (1). Remove the hood lock. Remove the lock drive cable (4). Installation Installation is carried out in the...

Hood release cable
Removal Remove: front bumper, hood lock, hood lock drive. Mark the routing of the hood lock cable. Disconnect the hood lock drive cable at point (1). Remove the headlight range control switch cables. Remove the cable...

Hood stop — removal and installation
Removal Caution! The gas-filled strut is installed in such a way as to prevent leakage. Before removing the gas-filled strut, mark the installation direction (body and rod), to return it to its original position....

Tailgate lock
Tightening torques: Tailgate lock mounting bolts - 8 Nm. Removal Remove the tailgate trim. Remove: screws (2), tailgate lock. Remove the rear door lock drive rod. Disconnect the tailgate lock connector (3). Installation...

Tailgate stop
Removal Before removing, mark the installation direction of the gas-filled strut. At point (1), detach the holders (2) using a flat-blade screwdriver without removing them. Remove the gas-filled strut while holding the...

External tailgate handle
Tightening torques: Tailgate handle mounting bolts - 8 Nm. Removal Remove the rear door trim. Disconnect the connector (1) from the outer tailgate opening handle. Disconnect the outer tailgate opening handle rod at...

Windshield — Removal and Installation
Removal Remove: interior rear view mirror, lining of the windshield pillars. Loosen the screw (1). Remove the decorative trim (2). Remove the trim. Partially remove the seals (3). Remove the windshield wiper arms. Apply...

Front door drop glass
Removal Remove the front door trim. Remove the inner window sill seal. Roll down the window. Remove the outer window sill seal. Loosen the bolts (1). Remove the glass. Installation Parts that must be replaced: bolt for...

Rear door drop glass
Removal Remove the rear door trim. Remove the inner window sill seal (1). Remove the gutter from the bracket. Remove the gutter fasteners. Roll down the window. Remove the outer window sill seal (2). Loosen the bolts...

Side glass of the body
Removal Remove: rear pillar trim, side trim of the rear shelf, upper trim of the rear pillar. Protect the side glass from damage by applying protective tape around the perimeter. Cut off the adhesive layer. Remove the...

Rear window — removal and installation
Removal Remove: rear door trim, rear window wiper lever, rear window wiper motor, high brake light. Disconnect the rear window defroster wire harness connectors. Protect the glass from damage by applying protective tape...

Front door glass guide channel
Removal Remove: front door trim, front door drop-down glass. Disconnect the front door glass guide channel at point (1), (2). Remove the front door glass guide channel. Installation Installation is carried out in the...

External window seal of the front door
Removal Roll down the window. Carefully remove the outer window sill seal (4) using the tool (Cag. 1363) (be careful not to damage the part). Installation Installation is carried out in the reverse order of removal.

External window seal of the rear door
Removal Roll down the window. Carefully remove the outer window sill seal (4) using the tool (Cag. 1363) (be careful not to damage the part). Installation Installation is carried out in the reverse order of removal.

Rear door glass guide channel
Removal Remove: rear side door trim, rear door drop-down glass. Remove the rear door guide channel in direction (2) and (3). Installation Install the rear side door glass guide channel. Install: rear door drop-down...

Front bumper assembly
1 - Front logo 2 - Upper trim of the front bumper 3 - Radiator grille 4 - Front bumper 5 - Lower grille of the front bumper 6 - Fog light bracket 7 - Fog light mounting clip 8 - Fog light 9 - Front bumper center trim

Rear bumper assembly
1 - Rear bumper 2 - Energy-absorbing support of the rear bumper 3 - Rear bumper trim 4 - Reflector 5 - Side bracket with spring retainer for rear bumper 6 - Rivet of the side bracket with a spring retainer of the rear...

Front outer body cladding
1 - Hood 2 - Front bumper 3 - Hood hinge 4 - Front wing 5 - Side bracket with spring retainer for front bumper 6 - Front bumper side bracket spring retainer rivet 7 - Front part of the threshold panel extension 8 -...

Front bumper — removal and installation
Removal Place the vehicle on a two-post lift. Remove: bolts for fastening the front mudguard on the front bumper on both sides of the car, lower front bumper mounting bolts. Remove the upper front bumper mounting bolts....

Rear bumper — removal and installation
Removal Place the vehicle on a two-post lift. Remove the rear lights on the wings. Remove: bolts for fastening the rear mudguard on the rear bumper on both sides of the car, lower rear bumper mounting bolts, upper rear...

Side outer body cladding
1 - Roof rack guide 2 - Front roof rack rail trim 3 - Rear roof rack rail trim 4 - Access hatch to the central mount 5 - Door sill panel trim 6 - Trim for threshold panel extension 7 - Front part of the threshold panel...

Front mudguard — removal and installation
Removal Place the vehicle on a two-post lift. Remove the front wheel from the appropriate side. Remove: front wheel arch shield mounting bolts, front wheel arch guard holders, front mudguard. Installation Installation...

Rear mudguard — removal and installation
Removal Place the vehicle on a two-post lift. Remove the rear wheel from the appropriate side. Remove: screws (1), holders (2), rear mudguard. Installation Check the condition of the holders and replace them if...

Outside rear view mirror
Removal Remove the front door trim. Disconnect the connector (1) (depending on the equipment level). Loosen the bolts (2). Remove the rear view mirror. Installation Installation is carried out in the reverse order of...

Glass of the outside rear view mirror
Removal Apply protective tape around the perimeter of the mirror. Remove the glass using the tool (Cag. 1363) as a lever. Disconnect the power wires from the terminals (depending on the equipment level). Installation...

Rear Logo — Removal and Installation
Removal Remove the rear logo using the tool (Car. 1363). Installation Secure the back logo with snaps.

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share with friends:

Other sections on other Renault models

➽ Body and interior: Exterior (external elements) Renault Laguna 2 (2001-2007)
➽ Body and interior: Exterior and interior Renault Kangoo 1 (1997-2007)
➽ Body and interior: Exterior (external elements) Renault Espace I and II (1984-1996)
➽ Body and interior: Exterior (external elements) Renault Clio 1 (1990-1998)
➽ Body and interior: Exterior (external elements) Renault Symbol 1 (1999-2008, petrol)
➽ Body and interior: Exterior (external elements) Renault Logan 2 (2012-2020)

Link to this section in different formats

TEXTHTMLBB Code

Duster 1 (2009-2017)