Gasoline engine K4M car Renault Duster 1

Lower engine cover
Tightening torques Bolts securing the oil pan to the cylinder block 14 Nm Engine oil pan to gearbox mounting bolts 44 Nm Mounting bolt for engine oil pan to multifunctional bracket 25 Nm Bracket mounting bolts 62 Nm...

Oil filter — removal and installation
Attention! Be sure to check the oil level using the dipstick. Do not allow the oil level to exceed the maximum level on the dipstick (this may lead to engine failure). Note: After pouring oil into the engine, before...

Oil pressure sensor
Tightening torques Oil pressure sensor 35 Nm Removal Place the vehicle on a two-post lift. Remove: engine oil pan protection mounting bolts, protective screen. Disconnect the wiring connector from the oil pressure...

Oil pump — removal and installation
Tightening torques Oil pump mounting bolts 25 Nm Removal Place the vehicle on a two-post lift. Drain the oil from the engine. Remove the engine oil pan. Remove: oil pump mounting bolts (1), oil pump. Installation Check...

Multifunctional bracket (motor air conditioner)
Tightening torques Bolts for fastening the multifunctional bracket to the cylinder block 44 Nm Lower mounting bolt of the multifunctional bracket on the engine oil pan 25 Nm Models with K4M engine, power steering and...

Multifunctional bracket (engine with heater)
Tightening torques Bolts for fastening the multifunctional bracket to the cylinder block 44 Nm Bolt for fastening the multifunctional bracket to the engine oil pan 25 Nm Removal Place the vehicle on a two-post lift....

Removal and installation the engine
Tightening torques Nut for fastening the silent block of the left support of the pendulum suspension 62 Nm Exhaust manifold flange mounting bolts 21 Nm Front Suspension Subframe Upper Tie Rod Bolts 21 Nm Bolts for...

Removal and installation the flywheel
Tightening torques: Flywheel bolts - 25 Nm + 50°±6°. Removal Remove: gearbox, clutch housing with pressure plate assembly. Lock the flywheel with the locking pin (Mot. 582-01) (1). Remove: flywheel mounting bolts,...

Compression Stroke End Pressure — Check
Remove: ignition coil wiring harnesses, spark plugs. Connect the compression tester for petrol engines (1). Fulfil the engine starting conditions: set the gear shift lever to neutral position, automatic transmission...

Auxiliary Drive Belt (Engine with Air Conditioning)
Tightening torques Automatic tension roller mounting bolts 21 Nm Idler pulley mounting bolt 21 Nm Caution: Do not run the engine without the accessory drive belt, as this may result in damage to the crankshaft pulley....

Auxiliary equipment drive belt (engine with heater)
Tightening torques: Automatic tension roller axle mounting bolt - 40 Nm. Caution: Do not run the engine without the accessory drive belt, as this may result in damage to the crankshaft pulley. Removal Place the vehicle...

Crankshaft pulley
Tightening torques Crankshaft pulley mounting bolt 40 Nm + 145°±15° Plug for the hole for the TDC locking pin 25 Nm Removal Place the car on a lift. Disconnect the battery. Remove: intake air duct, intake noise muffler,...

Timing belt
Tightening torques Timing Belt Idler Pulley Fastening Bolt 50 Nm Bolt for securing the new crankshaft pulley 40 Nm + 145°±15° Timing belt tension roller fastening nut 27 Nm Lower timing belt cover mounting bolts 12 Nm...

Cylinder head cover
Tightening torques Bolts 22, 23, 20 and 13 for fastening the cylinder head cover 8 Nm Bolts 1 - 12, 14-19, 21-24 for fastening the cylinder head cover 15Nm Bolts 22, 23, 20 and 13 for fastening the cylinder head cover...

Camshaft
Tightening torques: Camshaft stud - 8 Nm. Removal Place the vehicle on a two-post lift. Disconnect the battery. Remove: right front wheel, accessory drive belt, right support of the pendulum suspension, intake noise...

Camshaft oil seal on gearbox side
Tightening torques Intake camshaft pulley hub retaining nut 30 Nm + 84°±4° Exhaust camshaft pulley hub fastening nut 30 Nm + 84°±4° Removal Place the vehicle on a two-post lift. Disconnect the battery. Remove: right...

Oil separator — removal and installation
Tightening torques: New oil separator mounting bolts - 15 Nm. Removal Remove: intake noise muffler, oil separator mounting bolts, oil separator, air filter housing, throttle body, intake manifold, ignition coils....

Right engine pendulum mount support
Tightening torques Bolts securing the right pendulum support to the engine 62 Nm Bolts securing the right pendulum suspension support to the body 62 Nm Removal Remove the top engine cover. Fit the engine support device...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share with friends:

Other sections on other Renault models

➽ Power unit: Petrol engines 1.6 l Renault Logan 2 (2012-2020)
➽ Power unit: Petrol engines 1.8 l (F) Renault Clio 1 (1990-1998)
➽ Power unit: Petrol engines 2.0 l Renault Megane 1 (1995-2002)

Link to this section in different formats

TEXTHTMLBB Code

Duster 1 (2009-2017)