Car exhaust system Renault Duster 1

Location of components of the exhaust gas recirculation system (K9K)
1 - Exhaust gas recirculation solenoid valve 2 - Exhaust gas cooler 3 - Exhaust gas supply line 4 - Metal air duct 5 - Cooler support on the flywheel side of the engine 6 - Cooler bracket on the timing drive side

Adsorber — removal and installation (K4M)
Removal Place the car on a lift. Remove the right front wheel. Move the front part of the right front fender liner to the side. Disconnect: adsorber pipes (1), solenoid valve connector. Disconnect the breather tube (2)....

Exhaust Gas Recirculation Solenoid Valve (K9K)
Tightening torques: EGR solenoid valve mounting bolts - 10 Nm. Note: The exhaust gas recirculation solenoid valve is pressed into the exhaust gas recirculation unit. Removal Remove the air filter housing. Disconnect the...

Exhaust Gas Cooler (K9K)
Tightening torques Exhaust Gas Cooler Mounting Bolts 12 Nm Bolts securing the rigid exhaust gas recirculation pipeline 12 Nm Removal Place the vehicle on a two-post lift. Disconnect the battery. Remove: top engine...

Exhaust gas recirculation system
Tightening torques Exhaust gas recirculation unit mounting bolts 21 Nm Bolts for securing the lifting eye on the timing drive side and the metal air supply duct 10 Nm Removal Place the vehicle on a two-post lift....

Exhaust Gas Recirculation Pipe (K9K)
Tightening torques Cylinder head rigid exhaust gas recirculation pipe bracket mounting bolts 21 Nm Mounting bolts for rigid EGR pipe on exhaust manifold 36 Nm EGR rigid pipe mounting bolts to EGR unit 12 Nm Lifting eye...

List and location of exhaust system components
Models with K4M engine A - Cutting zone A B - Cutting zone B 1 - Sealing ring release pipelines 2 - Catalytic converter 3 - Downstream oxygen sensor 4 - Additional muffler 5 - Silent block of additional muffler 6 - Main...

Features of exhaust system repair
Parts and materials for repair Parts that must be replaced: exhaust pipe coupling (if there is one), gasket or sealing ring connecting the catalytic converter or pre-catalytic converter to the rest of the exhaust...

Catalytic converter (K9K engine)
Tightening torques Turbocharger outlet mounting studs 9 Nm Nuts securing the catalytic converter to the turbocharger 28 Nm Bolts securing the upper brace to the engine 44 Nm Bolt and nut for fastening the lower brace to...

Catalytic converter (K4M engine, 4x2 drive)
Tightening torques Exhaust manifold flange mounting bolts 21 Nm Oxygen sensor 45 Nm Removal Place the vehicle on a two-post lift. Disconnect the battery. Remove the downstream oxygen sensor connector from the holder by...

Additional muffler (K4M engine, 4x2 drive)
Removal Place the vehicle on a two-post lift. Place a hydraulic jack under the additional muffler. Determine the cutting area of the additional muffler. Cut the exhaust pipe using the tool (Mot. 1199-01) in specially...

Intermediate pipeline (K9K engine)
Tightening torques: Exhaust manifold coupling bolts - 25 Nm. Removal Place the vehicle on a two-post lift. Place a hydraulic jack under the intermediate pipe. Cut the exhaust pipe using tool Mot. 1199-01 in the middle...

Main muffler (4x2 drive)
Removal Place the vehicle on a two-post lift. Place a hydraulic jack under the muffler. Determine the area to cut the muffler. Using a device (Mot. 1199-01) for cutting off exhaust pipes in the cutting area. Remove the...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share with friends:

Other sections on other Renault models

➽ Power unit: Exhaust system Renault Symbol 1 (1999-2008, petrol)
➽ Power unit: Exhaust system Renault Laguna 2 (2001-2007)
➽ Power unit: Intake and exhaust system Renault Logan 2 (2012-2020)
➽ Power unit: Exhaust system Renault 19 (1988-1996)
➽ Power unit: Intake and exhaust system Renault Megan 2 (2002-2009, petrol)
➽ Power unit: Exhaust system Renault Scenic 1 (1996-2003)

Link to this section in different formats

TEXTHTMLBB Code

Duster 1 (2009-2017)