Automatic switching on of external lighting when the vehicle is parked Depending on the modification, the cars are equipped with a system for automatically switching on low beam headlights (with the engine not running) to illuminate the space in front of the car. This function is only...
Automatic switching on of exterior lighting while driving This function is switched on or off using the exterior lighting, turn signal and fog light switch if the CEC is configured correctly. With the engine stopped or the vehicle stationary with the engine running, press and...
Removal and installation a headlamp with a halogen lamp Removal Remove the front bumper. Fig. 7.6. Headlight lower mounting screws: 1 – screws Unscrew the screws of the lower headlight mount (Fig. 7.6). Fig. 7.7. Upper headlight mounting screw: 1 – screw Unscrew the upper...
Adjusting the headlight with a halogen lamp Place the vehicle on a level, horizontal surface. Adjust the air pressure in your tires to the correct level. Open the hood. Make sure there is no cargo in the luggage compartment. Note: Do not apply the parking brake....
Replacing halogen headlight bulbs The methods for replacing bulbs vary depending on the engine installed in the vehicle: 1. Through the hatch in the fender liner (Fig. 7.10); 2. Through the engine compartment. Fig. 7.10. Hatch in the mudguard, designed...
Removal and installation fog lights Removal Remove the front bumper. Fig. 7.15. Fog light mounting screws: 1 – screws Unscrew the screws securing the fog lights (Fig. 7.15). Installation When replacing, use only certified H11 bulb. Tighten the fog light...
Removal and installation the headlight corrector switch There are two models of the headlight corrector unit: with a brightness controller for the instrument lighting of the "basic configuration" - for models with manual control of the air conditioning system; with a...
Removal and installation the headlight corrector motor Note: To remove the corrector actuator, you must remove the headlight assembly. Removal Remove the headlight. Rotate the motor 1/8 turn outward to disconnect it from the headlight assembly. Fig. 7.19. Removing the...
Xenon headlights — general information These vehicles are equipped with: automatic adjustment system for each headlight depending on changes in body height, acceleration, braking and vehicle speed; headlight washer. Warning! Do not turn on the bulb when it...
Replacing xenon headlight bulbs Removal Disconnect the wires from the battery terminals, starting with the negative terminal. To replace the xenon lamp, you need to remove the headlight. Fig. 7.21. Removing a headlight with xenon lamps: 1 – latch To...
Removal and installation of xenon headlights ECU Removal Disconnect the battery. Remove the headlight. To avoid scratching the headlight, place it on a clean cloth. Fig. 7.24. Removing the "ECU - high voltage unit" unit: 1 – mounting screws Remove the screws securing...
Front headlight corrector height sensor Removal Disconnect the connector. Fig. 7.26. Removing the front headlight corrector height sensor: 1 – stopper; 2 – mounting bolt Remove the stopper and unscrew the front body height sensor mounting bolt (Fig. 7.26)....
Rear headlight corrector height sensor Removal Disconnect the connector. Fig. 7.27. Removing the sensor stopper: 1 – stopper Remove the stopper (Fig. 7.27). Fig. 7.28. Removing the sensor mounting bolt: 1 – bolt Unscrew the rear body height sensor mounting...
Removal and installation rear lights Removal Remove the rear light access cover. Fig. 7.29. Rear light connector Disconnect the rear light connector (Fig. 7.29). Unscrew the three mounting nuts and remove the rear light. Fig. 7.30. Fastening the rear light...
Removal and installation the upper brake light Removal Fig. 7.31. Removing the upper brake light cover: 1 - protrusions; 2 – lid Press on the tabs and remove the high brake light cover (Fig. 7.31). Fig. 7.32. Removing the high brake light: 1 – connector; 2 –...
Removal and installation the license plate light Removal Fig. 7.34. Removing the license plate light Remove the license plate light using a flat-blade screwdriver (Fig. 7.34). Disconnect the connector. Installation Installation is carried out in the reverse order of...
Features of the interior lighting design The cars are equipped with: separate lights for illuminating the lower part of the door (light up when the corresponding door or storage compartment in the floor is opened); interior lighting lampshades (front and back)...
Time delay action The interior lighting devices are switched on by command from the central electronic control system: when opening one of the side doors or the trunk door; when unlocking opening elements of the body by command from the...
Interior light Depending on the location of the interior light and the vehicle's trim level, the light may be equipped with: one switch for the central ceiling light; with a switch for the central ceiling light and directional lights;...
Removal and installation the interior light Removal Fig. 7.35. Disconnecting the diffuser: 1 – diffuser Remove the diffuser using a special tool (Cag. 1597), installing it on the right side of the lampshade (Fig. 7.35). Fig. 7.36. Removing the interior light: 1 –...
Mirror illumination lamp In addition to the mirrors, sun visors can be equipped with lights built into the roof lining. Fig. 7.37. Sun visor mirror switch: 1 – switch; 2 – visor fastening; 3 – mirror cover The switch is located on the sun visor...
Removal and installation the door sill light Removal Vehicles may be equipped with separate lights controlled by the UCH when the storage compartments under the floor on the driver's or passenger's side are opened. Fig. 7.39. Removing the door sill light: 1 –...