Features of the design of the body and interior of the car The body of Megane cars is a load-bearing four-door, consists of a frame and hinged elements. The body frame includes a base, sidewalls, roof and frame parts connected to each other by electric welding (point, seam and...
Body Damage Repair Before starting repairs, a number of checks must be made to ensure that the structural elements of the body, which provide the car's behavior on the road, were not damaged during the impact. As a rule, welded parts of...
Removal and installation of a forward bumper Removing Place the car on a lift. Pic. 8.3. Unscrewing the screws securing the lower base of the bumper: 1 - screws Loosen the screws (pic. 8.3). Pic. 8.4. Unscrewing the screws securing the bumper in the wheel arch: 1...
Removal and installation of a back bumper Remove the rear lights. Place the car on a lift. Pic. 8.19. Removing plastic rivets: 1 - rivets Remove plastic rivets (pic. 8.19). Pic. 8.20. Rear bumper lower mounting screws: 1 - screws Loosen the lower rear bumper...
Replacing the Outer Guide Pic. 8.23. Removing the guide pin: 1 - clamps Disconnect the clips and remove the guide tab (pic. 8.23). Buffer Replacement Remove the central plastic rivet. Drill out four rivets. Pic. 8.24. Removing the buffer Remove...
Removal and installation of a decorative overlay of a forward door Removing Pic. 8.25. Removing the plug: 1 - plug Remove the plug (pic. 8.25). Press the screwdriver on the locking tab. Pic. 8.26. Removing the decorative trim Remove the decorative trim by sliding it towards the rear of...
Removal and installation of a decorative overlay of a back door Withdrawal (first way) Pic. 8.28. Removing the wire pass plug at the bottom Partially detach the wire pass plug at the bottom (pic. 8.28). Press the screwdriver on the locking tab. Pic. 8.29. Removing the decorative...
Removal and installation of a protective level of a back wing Removing Pic. 8.32. Lining shift Slide the trim towards the front of the car (pic. 8.32) Rotate the rear holders a quarter of a turn and remove them. Pic. 8.33. Removing holders Installation Install the holders on the...
Removal and installation of a lattice of a niche of an air intake Removing Pic. 8.34. Removing the trim Detach the decorative trim (pic. 8.34). Disconnect the seal. Pic. 8.35. Removing the plastic rivets: 1 - rivets Disconnect the plastic rivets and remove the wiper arms using the...
Removal and installation of decorative overlays of average racks Removing Pic. 8.36. Removing the decorative trim: 1 - fastening screw; 2 - decorative overlay Unscrew the fastening screw and detach the decorative trim (pic. 8.36). Drill out the rivets. Remove the top bracket....
Removal and installation of an external rear-view mirror Removing Pic. 8.38. Removing the interior trim Remove the interior trim (pic. 8.38). Pic. 8.39. Removing the outside rear-view mirror: 1 - fastening bolt Unscrew the mounting bolt and remove the outside rearview mirror...
Removal and installation of glass of an external rear-view mirror Removing Protect the edges of the outside rearview mirror with protective tape. Pic. 8.41. Removal of glass of an external rear-view mirror Using a special tool (Sag. 1363) as a lever, release the glass (pic. 8.41)....
Removal and installation of the case of an external rear-view mirror Removing Protect the edges of the outside rearview mirror with protective tape. Using a special tool (Sag. 1363) as a lever, release the glass. Disconnect the power wires. Pic. 8.42. Releasing spring clips Pry out the...