Share with friends:
Doors, locks and windows of the car Renault Megane 2
Removal and installation the front side door lock cylinder
Removal Fig. 8.44. Removing the lock cylinder lining: 1 – cladding Remove the lock cylinder trim (Fig. 8.44). Fig. 8.45. Installing the hook: 1 – hook Insert a hook made from scrap materials into the hole (Fig. 8.45)....
Removal Fig. 8.44. Removing the lock cylinder lining: 1 – cladding Remove the lock cylinder trim (Fig. 8.44). Fig. 8.45. Installing the hook: 1 – hook Insert a hook made from scrap materials into the hole (Fig. 8.45)....
Removal and installation the outer door handle
Removal Protect your upholstery (for example, with a mastic knife). Fig. 8.51. Removing the window switch panel Disconnect the window switch panel (in the back) pliers for removing upholstery and trim holders (Fig....
Removal Protect your upholstery (for example, with a mastic knife). Fig. 8.51. Removing the window switch panel Disconnect the window switch panel (in the back) pliers for removing upholstery and trim holders (Fig....
Removal and installation the front side door lock
Remove the trim hatch and the front door outside handle. Remove the seal. Fig. 8.63. Removing the module from the door panel: 1 – stoppers Remove the two stoppers and the module from the door panel (Fig. 8.63)....
Remove the trim hatch and the front door outside handle. Remove the seal. Fig. 8.63. Removing the module from the door panel: 1 – stoppers Remove the two stoppers and the module from the door panel (Fig. 8.63)....
Car with presence sensor
Removal Fig. 8.65. Detaching the prism Disconnect the prism at points A and B using a flat-blade screwdriver (Fig. 8.65). Fig. 8.66. Putting the lock on the door frame hook: 1 – door frame hook Place the lock on the...
Removal Fig. 8.65. Detaching the prism Disconnect the prism at points A and B using a flat-blade screwdriver (Fig. 8.65). Fig. 8.66. Putting the lock on the door frame hook: 1 – door frame hook Place the lock on the...
Front side door electric window mechanism
Removal Remove the door trim. Fig. 8.67. Unscrewing the screws Remove the speaker grille and unscrew screws A (Fig. 8.67). Disconnect the window lift motor wiring harness. Fig. 8.68. Removing the window lift slider...
Removal Remove the door trim. Fig. 8.67. Unscrewing the screws Remove the speaker grille and unscrew screws A (Fig. 8.67). Disconnect the window lift motor wiring harness. Fig. 8.68. Removing the window lift slider...
Rear side door electric window lift mechanism
Removal Remove the door trim. Disconnect the wiring harness from the window lift motor. Fig. 8.69. Removing the window lift slider holders: 1 – slider holders Disconnect the door trim and the two window lift slider...
Removal Remove the door trim. Disconnect the wiring harness from the window lift motor. Fig. 8.69. Removing the window lift slider holders: 1 – slider holders Disconnect the door trim and the two window lift slider...
Removal and installation the seal of the opening of the side front door
Removal Remove the outside rearview mirror. Fig. 8.70. Removing the window sill seal Carefully detach the window sill seal at points A and B using a special tool (Cag. 1363) (Fig. 8.70). Fig. 8.71. Removing the groove...
Removal Remove the outside rearview mirror. Fig. 8.70. Removing the window sill seal Carefully detach the window sill seal at points A and B using a special tool (Cag. 1363) (Fig. 8.70). Fig. 8.71. Removing the groove...
Removal and installation the side rear door opening seal
Removal Remove the door trim. Fig. 8.73. Removing the window sill seal Disconnect the outer window sill seal at points A and B using a special tool (Cag. 1363) (Fig. 8.73). Fig. 8.74. Removing the internal window sill...
Removal Remove the door trim. Fig. 8.73. Removing the window sill seal Disconnect the outer window sill seal at points A and B using a special tool (Cag. 1363) (Fig. 8.73). Fig. 8.74. Removing the internal window sill...
Replacing the sunroof sealing gasket
Attention! The removed seal must be replaced. Clean and then degrease the bonding area with heptane. Fig. 8.78. Laying the seal in the rear middle part: 1 – middle part Position the seal joint in the rear center section...
Attention! The removed seal must be replaced. Clean and then degrease the bonding area with heptane. Fig. 8.78. Laying the seal in the rear middle part: 1 – middle part Position the seal joint in the rear center section...
Removal and installation bonnet sound insulation
Removal Fig. 8.79. Removing the trim holders Using trim and panel retainer pliers, detach the five retainers (Fig. 8.79). Remove the hood sound insulation. Installation Replace the holders if necessary. Installation is...
Removal Fig. 8.79. Removing the trim holders Using trim and panel retainer pliers, detach the five retainers (Fig. 8.79). Remove the hood sound insulation. Installation Replace the holders if necessary. Installation is...
Removal and installation the front side door drop glass
Removal Open the hatch on the door trim. Fig. 8.80. Installing the glass in a position that allows access to the holders: 1 – holders Position the glass so that you can access the two holders (Fig. 8.80). Fig. 8.81....
Removal Open the hatch on the door trim. Fig. 8.80. Installing the glass in a position that allows access to the holders: 1 – holders Position the glass so that you can access the two holders (Fig. 8.80). Fig. 8.81....
Removal and installation the rear side door drop glass
Removal Open the hatch on the door trim. Remove the outer window sill seal using a special tool (Cag. 1363). Fig. 8.83. Installing the glass in a position that allows access to the holder: 1 – holder Position the glass...
Removal Open the hatch on the door trim. Remove the outer window sill seal using a special tool (Cag. 1363). Fig. 8.83. Installing the glass in a position that allows access to the holder: 1 – holder Position the glass...
Removal and installation the windshield
Removal Caution! To avoid rain sensor malfunction, install a windshield of the same tint. The old rain sensor must remain on the old windshield for the entire duration of the replacement operation. Note: When removing,...
Removal Caution! To avoid rain sensor malfunction, install a windshield of the same tint. The old rain sensor must remain on the old windshield for the entire duration of the replacement operation. Note: When removing,...
This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Other sections on other Renault models
➽ Body and interior: Doors, locks and windows Renault Symbol 1 (1999-2008, petrol)
➽ Body and interior: Doors, locks and windows Renault Logan 1 (2004-2012, petrol)
➽ Body and interior: Doors, locks and windows Renault Sandero 1 (2007-2012, petrol)
➽ Body and interior: Doors, locks and windows Renault Kangoo 1 (1997-2007)
➽ Body and interior: Doors, locks and windows Renault Scenic 1 (1996-2003)
➽ Body and interior: Doors, locks and windows Renault Clio 1 (1990-1998)
Link to this section in different formats
TEXTHTMLBB Code
- User manual
- Introduction to manual
- Controls and instruments
- Salon equipment
- Operation and driving
- Maintenance and care
- Power unit
- Engine repair
- Fuel system
- Injection system
- Intake and exhaust system
- Starting and charging system
- Cooling system
- Decreased toxicity
- Transmission
- Clutch
- Mechanical gearbox
- Automatic gearbox
- Wheel drive mechanism
- Chassis, running gear
- Suspension and wheels
- Steering
- Brake system
- Body and interior
- Exterior (external elements)
- Interior (internal elements)
- Doors, locks and windows
- Heating and air conditioning
- Electrical equipment
- Equipment and devices
- Headlights and lighting
- Electrical circuits
- General information
- User manual
- Maintenance
- Power unit
- Petrol engines 1.4/1.6 l
- Petrol engines 2.0 l
- Diesel engines 1.9 l
- Overhaul of engines
- Cooling system
- Fuel system (petrol)
- Fuel system (diesel)
- Decreased toxicity
- Charge and launch systems
- Ignition system (petrol)
- Preheat system (diesel)
- Transmission
- Clutch
- Mechanical gearbox
- Automatic gearbox
- Drive shafts
- Chassis, running gear
- Brake system
- Car suspension
- Steering
- Body and interior
- Exterior (external elements)
- Interior (internal elements)
- Doors, locks and windows
- Electrical equipment
- Equipment and devices
- Electrical circuits