Steering
Construction type - Power rack and pinion steering
Front suspension
Wheel alignment data
Longitudinal inclination of the kingpin
early models (J11...) — 3° 25 ± 20'
Later models (J63...) — 4 ±20'
Camber
early models (J11...) — 0° 20' ± 30'
Later models (J63...)
Negative camber - 0°8'±30'
Kingpin transverse tilt
early models (J11...) — 13 ±30'
Later models (J63...) — 12° 45’ ±30'
Toe adjustment
early models (J11...) — -4.0±2 mm
Later models (J63...) — -4.5±0.7 mm
Rear suspension
Type of construction - Axle beam with trailing arms, springs, transverse arm extensions, and hydraulic telescopic shock absorbers.
Wheel alignment data:
- Camber - 0°30'±30', not adjustable
- Test conditions The vehicle is unloaded, has an operating weight
- Toe-in -1.0... -4.0 mm, not adjustable
- Test conditions The vehicle is unloaded, has an operating weight
Tightening torques - Nm
Steering
Nuts, tie rod joints
Locknuts, tie rod inner ball joints - 50
Steering gear bolts - 40
Wheel bolts, 4 bolts - 90
Wheel bolts, 5 bolts - 100
Contact bolts, control hinge - 25
steering wheel nut
Steering column shaft mounting
Front suspension
Vehicles with «J11...» in the serial number
Suspension Ball Joint Nuts - 65
Nut of a bolt of a cover of the bearing of the top wishbone - 95
Lower control arm bearing cap bolt nut:
- Until January 1988 - 90
- Since January 1988 - 130
- Shock absorber lower bolt - 80
Shock absorber locknut:
- Until January 1988 - 40
- Since January 1988 - 60
Upper Shock Mount - 15
Suspension arm stretch - 70
Drive Shaft Nuts - 250
Tie rod nuts - 40
Front wheel bearing caps - 15
Brake disc to wheel hub - 15
Stabilizer bolts - 15
Suspension hinges to arms - 25
Caliper strut bolts - 100
Disc brake caliper guide bolts - 35
Wheel bolts - 90
Vehicles with «J63...» in the serial number
Upper and lower ball joint nuts - 65
Nut of a bolt of a cover of the bearing of the top wishbone - 95
Wishbone Lower Mount:
Front mount - 135
Bottom mount - 45
Shock absorber lower bolts - 80
Shock absorber locknut - 60
Shock absorber to the body - 25
Piston rod to the upper support bearing - 20
Nut thrust - 70
Axle nut - 250
Tie rod nuts - 40
Tie Rod Lock Nut - 35
Wheel bearing cap to hub - 15
Brake disc to wheel hub - 15
Bolts of fastening of the stabilizer of cross-section stability — 15
Ball joints to suspension arms - 25
Caliper strut bolt - 100
Disc brake caliper guide bolts - 35
Wheel bolts, 4 bolts - 90
Wheel bolts, 5 bolts - 100
Rear suspension
Upper Shock Mount - 50
Shock Absorber Lower Mount - 25
Stretching the transverse suspension arm to the bridge and the body - 50
Longitudinal suspension arms to the body - 90
Axle ends to the bridge - 22
Nut of a nave of a back wheel — 160
Bolts at the top of the spring - 25
Brake drum mounting bolts - 15
Union nuts of the pipeline of a brake drive — 13
Bleeding plug - 6-8
Rack of a support of a disk brake to the back bridge — 70
Brake discs to the hub - 10
Wheel bolts - see «Front suspension»