Front seats with manual adjustment
To move the seat forward or backward, lift handle 1 to unlock the seat. Once the seat is in the desired position, release the handle and check that it is secure.
To raise or lower the seat cushion, pull lever 2 up or down as many times as necessary. To adjust the seatback angle, turn knob 3.
Heated seats
With the engine running, turn knob 4 to one of positions 1, 2 or 3 (depending on the desired temperature).
The warning light on the instrument panel will come on as soon as the heating system of one of the front seats is switched on.
The temperature stabilizing system determines, depending on the selected position, whether heating is necessary or not.
Driver's seat lumbar adjustment
Lower switch lever 5 to increase the support and raise the lever to decrease it.
The passenger seat back can recline on the cushion, forming «table».
Lower the head restraint, slide the seat back, fold out the handle b and lower the seat completely.
Front seats electrically adjustable
Switch 3 adjusts the backrest and switch 4 adjusts the seat cushion.
On vehicles equipped with this system, buttons 1 are used to memorize the selected position of the driver's seat.
To move the seat cushion, move switch 4 forward or backward.
To raise or lower the seat cushion, pull switch 4 up or down.
Lower switch lever 5 to increase the support and raise the lever to decrease it.
Storing the position of the driver's seat
Adjust the seat using switches 4 and 5.
Press one of the buttons 1, 2 or 3 and keep it pressed until a beep sounds to indicate that the driver's seat position has been memorized.
To memorize other positions, repeat the procedure for other buttons.
Returning the driver's seat to a stored position
With the vehicle stopped, press button 1, 2 or 3 once, depending on the desired seat position memorized.
Note. The return to the stored position is aborted by pressing one of the seat adjustment switches.
While the vehicle is moving, it is not possible to return to the position stored in the memory.
Access to rear seats (3-door body)
Seats with manual adjustment: lift handle 1 and move the seat forward.
To return the seat to its original position, bring its back to its original position.
Power seats: Raise handle 1 and recline the backrest fully to move the seat forward.
To return the seat to its original position, bring its back to its original position.
Front headrest
Raising the headrest: Pull the headrest up to the desired height.
Lowering the head restraint: press button 2 and hold the head restraint to the desired height adjusting the angle of the head restraint: move the front part A of the head restraint forward or backward for maximum comfort.
Removing the head restraint: Move the head restraint to its highest position (if necessary, tilt the seat back). Press button 1, raise the head restraint and remove it.
Headrest installation
Pull out guides 3 to the stop by pulling upwards. If you have difficulty, make sure that the grooves on the rails face the front of the vehicle.
Insert the headrest rods into the holes in the guide bushings (tilt the seat back if necessary).
Lower the head restraint as far as it will go and make sure it locks in place, then press button 1 and lower the head restraint as far as it will go. Make sure that each rail 3 is securely fixed in the seatback by pulling or pressing on them.
Rear seat head restraints
Raise or lower the head restraint while moving it forward to set it to the working position.
To remove, press tabs A on rails 1 and 2 of the head restraint and pull it out at the same time.
To install, insert the headrest rods into the holes in the guide bushings and lower the headrest to the first mark.
To set the head restraint to its lowest position (IN) lower the head restraint as far as it will go, then press the latch 2 and lower it completely.
Folding the rear seats
To fold seat cushion B, tilt it toward the front seats. With the seat cushion folded down, remove the rear seat headrests, then press button 1 and lower the backrest (And) seats C.